vauxhall Workshop Repair Guides

Vauxhall Workshop Service and Repair Manuals

ABOUT US
C-010 Control Unit Hard- and Software 1 > < C-008 Release Circuit

Astra H

C-009 - Telltale Circuit

Test

Work Order Description

Nominal Value
T001

Check: Short to Ground/Interruption of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    S115 Switch Unit - Driver Door
  • Ignition ON
  • Measure voltage between:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    Ground

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:
T002

Check: Circuit Interruption of Ground Circuit
  • Measure voltage between the following terminals:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 32

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:
T003

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Vehicle with REC (Rear Electronic Module)
Yes: No:
T004

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Front Electrical Sliding Roof
Yes: No:
T005

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

4 Doors
Yes: No:
T006

Check: Short to Ground of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X131 Rear Electronic Module
    (Wiring Harness Connector XR5 )
    &
    M1_M16 Motor - Sun Roof
  • Measure resistance between:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T007

Check: Interruption of Voltage Supply Circuit
  • Measure resistance between the following terminals:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    X131 Rear Electronic Module
    Wiring harness connector (wiring harness side) terminal 6 (XR5)

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T008

Check: Short to Ground/Interruption of Voltage Supply Circuit
  • Disconnect wiring harness connector from:
    S112P Switch Unit - Front Passenger Door
  • Measure resistance between:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T009

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Driver Door Handle Illumination, Front Passenger Door Handle Illumination
Yes: No:
T010

Check: Component
  • Disconnect wiring harness connector from:
    E72D Lamp - Driver Door
  • Measure resistance between:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    Ground
  • Disconnect each of the following components/control units consecutively from the wiring harness and repeat the measurement each time:
    E72P Lamp - Front passenger door

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T011

Check: Short to Ground/Interruption of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X131 Rear Electronic Module
    (Wiring Harness Connector XR5 )
  • Measure resistance between:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T012

Check: Interruption of Voltage Supply Circuit
  • Ignition OFF
  • Remove electrical component from socket:
    FE33 Fuse
  • Ignition ON
  • Measure voltage between:
    FE33 Fuse
    Input contact
    &
    Ground

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:


Result

Cause Of Fault
E001 Result: Defective Component
  • Defective component:
    S115 Switch Unit - Driver Door
E002 Result: Interruption
  • Circuit interruption between:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 32
    &
    Ground
E003 Result: Defective Component
  • Defective component:
    X131 Rear Electronic Module

Note:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E004 Result: Interruption
  • Circuit interruption between:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    X131 Rear Electronic Module
    Wiring harness connector (wiring harness side) terminal 6 (XR5)
E005 Result: Defective Component
  • Defective component:
    S112P Switch Unit - Front Passenger Door
E006 Result: Defective Component

If the nominal value is reached during one of the measurements, there is a short to ground in the circuit behind the component that has been disconnected immediately before that measurement, or the corresponding component is defective.
E007 Result: Short to Ground
  • Short circuit to ground between:
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26
    &
    X131 Rear Electronic Module
    Wiring harness connector (wiring harness side) terminal 6 (XR5)
    &
    Wiring harness connector terminals of all components (wiring harness side), which were disconnected from the wiring harness during this troubleshooting session
E008 Checking Procedure Validity

The selected Checking Procedure is not valid for this vehicle configuration.
E009 Result: Interruption
  • Circuit interruption between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 39 (XE2)
    &
    S115 Switch Unit - Driver Door
    Wiring harness connector (wiring harness side) terminal 26

or

  • Defective component:
    X125 Underhood Electronic Module

Note:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E010 Result: Defective Component
  • Defective component:
    X125 Underhood Electronic Module

Note:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.





C-010 Control Unit Hard- and Software 1 > < C-008 Release Circuit