DTC P2454 or P2455
Diagnostic Instructions
DTC Descriptors
DTC P2454 00: Diesel Particulate Filter (DPF)
Differential Pressure Sensor Circuit Low Voltage |
DTC P2455 00: Diesel Particulate Filter (DPF)
Differential Pressure Sensor Circuit High Voltage |
DTC P2455 01: Diesel Particulate Filter (DPF)
Differential Pressure Sensor Circuit Short to Battery |
DTC P2455 11: Diesel Particulate Filter (DPF)
Differential Pressure Sensor Circuit High Input |
Diagnostic Fault Information
Circuit
|
Short to Ground
|
Open/High Resistance
|
Short to Voltage
|
Signal Performance
|
5V Reference
|
P0641
|
P2454 00
|
P0641
|
P2453
|
Signal
|
P2454 00
|
P2455 01
|
P2455 01
|
P2453
|
Low Reference
|
-
|
P2455 01
|
-
|
P2453
|
|
|
Circuit/System Description
The diesel exhaust aftertreatment system consists of an under
hood pre-catalyst and an underbody catalyst. The underbody catalyst
also consists of the main diesel oxidation catalyst and the coated
diesel particulate filter (DPF). One of the main purposes of the
DPF is to collect particulates from the engine exhaust in order to
minimize discharge of soot to the atmosphere. The soot particles
accumulate in the channels of the DPF and are burned off at regular
intervals through a process called regeneration. This prevents the
DPF from clogging. The ECM commands the DPF regeneration after
calculating various vehicle conditions such as DPF pressure
difference, exhaust gas temperature, engine oil quality, engine
speed, etc. Excessive accumulation of the soot in the DPF can cause
a drop in the engine performance. During regeneration, additional
fuel is injected via multiple post injections in order to increase
the exhaust gas temperature. During this period, the DPF
temperature is raised to approximately 600°C (1 112°F) and
the accumulated soot is oxidized or burned off into carbon dioxide
(CO2).
Conditions for Running the DTC
• |
The ignition is ON, or the
engine is running. |
• |
The DTCs run continuously when
the above condition is met. |
Conditions for Setting the DTC
P2454
The ECM detects an open circuit or a short to ground greater than 2
s.
P2455
The ECM detects the DPF differential pressure sensor signal is
greater than 4.9 V for greater than 1 s.
Action Taken When the DTC Sets
• |
DTCs P2454, P2455 00 and P2455
11 are Type C DTCs. |
• |
DTC P2455 01 is a Type A
DTC. |
Conditions for Clearing the DTC
• |
DTCs P2454, P2455 00 and P2455
11 are Type C DTCs. |
• |
DTC P2455 01 is a Type A
DTC. |
Reference Information
Schematic Reference
Engine Controls Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Exhaust Particulate Filter System Description
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
1. |
Engine idling, observe the
scan tool diesel particulate filter data parameter. The reading
should be within 0-10 kPa (0-1.5 PSI). |
2. |
Operate the vehicle within the
Conditions for Running the DTC to verify the DTC does not reset.
You may also operate the vehicle within the conditions that you
observed from the Freeze Frame/Failure Records data. |
Circuit/System Testing
1. |
Ignition OFF, disconnect the
harness connector at the B154 Diesel Particulate Filter Exhaust
Differential Pressure Sensor. |
2. |
Test for less than 5 Ω
between the low reference circuit terminal 2 and ground.
|
⇒ |
If greater than the specified range, test the low
reference circuit for an open/high resistance. If the circuit tests
normal, replace the K20 Engine Control Module. |
3. |
Ignition ON, test for 4.8-5.2
V between the 5 V reference circuit terminal 1 and ground.
|
⇒ |
If less than the specified range, test the 5 V
reference circuit for a short to ground or open/high resistance. If
the circuit tests normal, replace the K20 Engine Control
Module. |
⇒ |
If greater than the specified range, test the 5 V
reference circuit for a short to voltage. If the circuit tests
normal, replace the K20 Engine Control Module. |
4. |
Verify the scan tool DPF
Differential Pressure Sensor parameter is greater than 4.8
V. |
⇒ |
If less than the specified range, test the signal
circuit for a short to ground. If the circuit tests normal, replace
the K20 Engine Control Module. |
5. |
Install a 1 A fused jumper
wire between the signal circuit terminal 3 and ground. Verify the
scan tool DPF differential pressure sensor parameter is less than
0.5 V. |
⇒ |
If greater than the specified range, test the
signal circuit for a short to voltage or an open/high resistance.
If the circuit tests normal, replace the K20 Engine Control
Module. |
6. |
If all circuits test normal,
replace the B154 Diesel Particulate Filter Exhaust Differential
Pressure Sensor. |
Repair Instructions
Perform the
Diagnostic Repair Verification after completing the diagnostic
procedure.
|