J462400 Toothed Belt, Replace (Y 17 DTL, without
AC, LHD)
Note: KM-6394 must be used from model year 04 instead of
KM-6169-1 .
1. Open bonnet
Caution!
On vehicles from model year 04 with ESP - the steering angle
sensor loses its basic adjustment each time the battery is
disconnected. It must be recalibrated.
2. Disconnect battery
3. Detach front right wheel
4. Raise vehicle
5. Remove front right wheel
6. Raise vehicle
7. Remove ribbed V-belt cover
- Remove 3 bolts (1)
- Remove clip (arrow).
|
|
8. Attach KM-6169 (1)
- Place left of KM-6169 onto front axle body (arrows, illus.
I)
- Note! Guide pin must be seated in bore in front axle body
- Attach both right holders on the front axle body (arrows,
Illus. II).
- Note! Guide pin must be seated in bore in front axle body
(arrows, Illus. III)
- Tighten bolts
|
|
9. Install support
- To KM-6169
- Adjust bracket (2) for support
- Screw on nut (1)
|
|
10. Adjust supports
- Transmission side
- Note! Turn spindles until the mounts (3) are positioned at the
guide journals free of play
- Engine timing side
- Insert journal of the support in the bore of the cylinder block
without play (arrow)
- Tighten nuts (1)
11. Lower vehicle
|
|
12. Remove air cleaner housing (1)
- Remove wiring harness plug for hot film mass air flow meter
(3)
- Release in direction of arrow
- Remove air intake hose (4)
- Remove bolt (2)
13. Remove right engine damping
block
|
|
14. Detach alternator wiring
harness
- Disconnect wiring harness plug
- Unscrew nut
15. Remove wiring trough (1)
- Unclip vacuum lines (2)
- Unclip wiring trough
- Remove bolt (3)
|
|
16. Loosen upper part of toothed belt
cover
- Remove 8 bolts
- Note! Note dissimilar bolt lengths
|
|
17. Detach right engine bracket (1)
- Remove 3 bolts
- Remove right engine bracket, right engine bracket adapter,
upper part of toothed belt cover
|
|
18. Raise vehicle
19. Loosen coolant pump ribbed V-belt
pulley (1)
|
|
20. Remove ribbed V-belt
- Tension ribbed V-belt tensioner in direction of arrow
- With KM-913-A
- Note! Mark running direction
21. Detach coolant pump ribbed V-belt
pulley
22. Remove torsional vibration damper
(1)
|
|
23. Detach lower part of toothed belt
cover
|
|
24. Set 1st cylinder to TDC
- Turn crankshaft evenly until TDC-fixing bolts can be
inserted
- Camshaft gear (M6) (1)
- Injection pump gear (M8) (2)
- Note! The mark on toothed belt drive gear must align with lug
on oil pump cover (arrows)
|
|
25. Lower vehicle
26. For toothed belt tension roller
with leaf spring:
- loosen toothed belt tensioner
- Screw in bolt (M10) in lower bore (3) of toothed belt
tensioner
- Loosen bolt (2)
- Remove tension spring (1)
|
|
27. For toothed belt tension roller
with spiral spring:
- Loosen toothed belt tension roller (1)
- Rotate toothed belt tension roller anticlockwise approx.
90°
- Tighten bolt (2)
|
|
28. Remove toothed belt
29. Install toothed belt
- Position toothed belt
- Note! Toothed belt must be taut from toothed belt drive gear
via oil pump drive gear and injection pump drive gear
- For toothed belt tension roller with leaf spring:
- Unscrew TDC-fixing bolt
- Rotate crankshaft 60° against direction of engine
rotation
- Tighten bolt of toothed belt tension roller
- For toothed belt tension roller with spiral spring 49 Nm
- For toothed belt tension roller with leaf spring 38.2 Nm
- For toothed belt tension roller with leaf spring: unscrew bolt
(M10) from lower bore of toothed belt tensioner
31. Timing, Check
- Turn crankshaft approx. 780° in direction of engine
rotation
- Mark on toothed belt drive gear (2) must align with casting lug
at oil pump cover (1)
- Screw in TDC-fixing bolts (arrows)
- Install torsional vibration damper
- Note! Mark on torsional vibration damper (3) must align with
pin (4) on oil pump cover If the TDC fixing bolts cannot be
inserted, the basic adjustment must be repeated
- Unscrew TDC-fixing bolts
|
|
31. Remove torsional vibration damper
32. Attach lower part of toothed belt
cover
- Tighten bolts (9.8 Nm / 7.2 lbf. ft.)
33. Attach right engine bracket
- Insert lower bolt
- Into right engine bracket and right engine bracket adapter
- Insert right engine bracket, right engine bracket adapter,
upper part of toothed belt cover
- Install 2 upper bolts
- Tighten 3 bolts (40 Nm / 29.5 lbf. ft.)
34. Fasten upper part of toothed belt
cover
- Tighten bolts (9.8 Nm / 7.2 lbf. ft.)
- Note! Note dissimilar bolt lengths
35. Attach coolant pump ribbed V-belt
pulley
36. Raise vehicle
37. Install torsional vibration
damper
- Tighten bolts (19.6 Nm / 14.5 lbf. ft.)
38. Install ribbed V-belt
- Note! Observe running direction and installation position
- Release ribbed V-belt tensioner
39. Fasten coolant pump ribbed V-belt
pulley
- Tighten bolts (9.8 Nm / 7.2 lbf. ft.)
40. Lower vehicle
41. Install right engine damping
block
- To side member
- Tighten bolts (40 Nm / 29.5 lbf. ft.)
- On engine bracket
- Tighten bolts (60 Nm/44 lbf. ft + 30° + 15°.)
42. Attach wiring trough
- Clip-in wiring trough
- Clip in vacuum lines
- Tighten bolt
43. Attach alternator wiring
harness
- Connect wiring harness plug.
- Tighten nuts
44. Install air cleaner housing
- Tighten bolt
- Fasten air intake hose.
- Tighten clamp (3.5 Nm / 2.6 lbf. ft.)
- Connect wiring harness plug to hot film mass air flow
meter
45. Raise vehicle
46. Detach support
47. Remove KM-6169
48. Install ribbed V-belt cover
- Screw in bolts
- Install clip
49. Lower vehicle
50. Install front right wheel
51. Lower vehicle
52. Attach front right wheel
- Tighten bolts (110 Nm / 81 lbf. ft.)
53. Connect battery
54. Calibrate steering angle sensor
Note: Rotate the
steering wheel one time from its right-hand to its left-hand
stop.
55. Program volatile memories
56. Close bonnet
|