Vauxhall Workshop Service and Repair Manuals

KM-113-2

Bracket

Mount for transmission holder with KM-910

KM-161-B

Bearing Puller

To remove various transmission parts

KM-204

Installer Sleeve

To push roller bearing into converter housing

KM-305

Remover / Installer

To remove and install various bearings in the transmission with KM-710

KM-313

Sliding Hammer

To pull axle shaft from transmission in conjunction with KM-902

KM-372-2

Installer

To press tapered roller bearing outer race into transmission housing with KM-554 and KM-710

KM-396

Ring pliers

To remove and install various retaining rings

KM-446

Installer Drift

To drive in axle shaft seal rings flush

KM-470-B

Angular Torque Wrench

For use when tightening all bolt connections with torque data including angles

KM-483

Adapter

To remove roller bearing out of converter housing with KM-J-26941 and KM-313

KM-498-B

Pressure Gauge

To check fluid pressure in conjunction with KM-580 and KM-892

KM-502-A

Spacer

To disconnect various transmission parts using KM-556-A

KM-507-C

Remover

Pressing tie rod joint out of steering knuckle

KM-514

Installer Sleeve

Remove and push in various transmission parts

KM-519

Installer Drift

To drive in axle shaft seal rings flush

KM-523

Remover / Installer

To press tapered roller bearing outer race for differential and friction washer in converter housing with KM-514 and KM-711-3.

KM-536-A

Friction Coefficient Meter

To measure slip torque of differential in conjunction with KM-995 or KM-6037

KM-554

Installer

To press tapered roller bearing into transmission casing

KM-556-A

Puller Set

To pull off various transmission parts

KM-557-A

Puller Set

To pull axle shaft seal rings from transmission

KM-567

Remover / Installer

To press tapered roller bearing inner race in differential with KM-514

KM-580

Adapter

To check fluid pressure in conjunction with KM-498-B

KM-586

Remover Hook

To drive out fluid pressure pump seal ring in conjunction with KM-J-7004

MKM-610

Torque Wrench

Range: 30–130 Nm . Use when tightening all bolted connections to torque

MKM-611

Torque Wrench

Range: 10–60 Nm . Use when tightening all bolts to torque

KM-620-B

Remover / Installer

To clamp various clutches in conjunction with KM-J-23078-A

KM-629-A

Ring Installer

To press roller bearing in auxiliary housing

KM-674-A

Installer

To install fluid pump seal ring

MKM-691

Remover

To pull out various bearings in conjunction with KM556–A

KM-697

Installers

To install various bearing rings in transmission

KM-710

Installer

To install tapered roller bearing outer race in transmission housing with KM-372-2, KM-554 and KM-305

KM-711

Installer

To push tapered roller bearing outer races for differential into transmission casing with KM-523-4 and KM-372-2.

MKM-883-1

Engine Bridge

To hold / lower / lift engine

MKM-892

Adapter

To check fluid pressure in conjunction with KM-498-B

KM-899

Remover / Installer

To remove and install converter

KM-902

Remover

Remove axle shaft from transmission with KM-313

KM-904

Base Frame

To remove and install front axle body with KM-6168 and KM-6169

KM-910

Transmission Holder

To hold transmission with KM-113–2

KM-911

Flywheel Holder

To hold flywheel

MKM-932-22

Contact Releaser

To release electrical contacts

KM-924

Closure Plugs

To close off fluid cooler lines

KM-962-A

Tester

To check and adjust selector lever position switch in conjunction with KM-962-10

KM-994

Adapter

Sleeve adapter for compressed air gun

KM-6037

Adapter

To turn differential completely to measure slip torque using MKM-536–A

KM-6168

Centring Equipment

To remove and install and centre front axle body with KM-904

KM-6169

Engine/Transmission Mount

To position the engine/transmission unit when removing and installing front axle body with KM-904 and KM-6168

KM-6181

Spring Pin

Steering intermediate shaft adjustment

KM-6388

Bracket

Secure torque converter so it does not fall

MKM-J-6459-B

Torque Wrench

Range: 0–9 Nm . For use when tightening all bolted connections to torque

MKM-J-7004

Slide Hammer

To remove fluid pump seal ring with KM-586

KM-J-23078-A

Clutch Tensioner

Disassembly and assembly of various clutches

KM-J-26941

Remover

Roller bearing from converter housing with KM-313 and KM-483

DT-47648

Transmission holder

To remove, install and hold transmission