Self-diagnosis
Display group overview
|
---|
Display group 0 (decimal displayed value)
|
Test conditions
▪ Engine runs at idling speed
▪ The coolant temperature is at least 80 °C
▪ The electrical consumers are switched off
|
Display zones
|
|
Specification
|
Corresponds to
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
Engine speed
|
65...75
|
650...750 rpm
|
|
|
|
|
|
|
|
|
|
Injection period
|
10...21
|
3.9...8.1 ms
|
|
|
|
|
|
|
|
|
Throttle valve angle
|
8...15
|
3.6...6.3 <°
|
|
|
|
|
|
|
|
Lambda probe status
|
0...4
|
---
|
|
|
|
|
|
|
Lambda integrator
|
102...154
|
128 = Lambda 1
|
|
|
|
|
|
Lambda probe signal
|
0...205
|
0...1.0 V
|
|
|
|
|
Engine load
|
40...68
|
2.0...3.4 ms
|
|
|
|
Coolant temperature
|
176...229
|
80...115 °C
|
|
|
Battery voltage
|
176...213
|
12.0...14.5 V
|
|
Intake air temperature
|
75...158
|
15...70 °C
|
|
Display zones
|
|
1
|
2
|
3
|
4
|
Display group 1
|
Display
|
xxxxrpm
|
xx.x °C
|
x.x V
|
xxxxxxxx
|
Indicated
|
Engine speed
|
Coolant temperature
|
Lambda probe voltage
|
Adjustment conditions2)
|
Specification1)
|
650...7502)
|
80...115
|
0...1.0 fluctuating
|
00000000
|
Display group 2
|
Display
|
xxxx rpm
|
xx.x ms
|
xx.x V
|
xx.x °C
|
Indicated
|
Engine speed
|
Injection period
|
Battery voltage
|
Intake air temperature
|
Specification1)
|
650...7502)
|
3.9...8.1
|
12.0...14.5 V
|
15...70
|
1)
The specifications must be attained when:
- engine runs at idling speed,
- the coolant temperature is at least 80 °C and
- electrical consumers are switched off
2)
Under the following conditions the idling speed is raised by the control unit:
- Battery voltage too low: up to 900 rpm
- After a long full throttle drive and at higher temperatures: up to 960 rpm
3)
Significance of numbers in 8 digit number block
.
|
---|
|
Display zones
|
|
1
|
2
|
3
|
4
|
Display group 3
|
Display
|
xxxx rpm
|
xx.x ms
|
xx <°
|
xx.x V
|
Indicated
|
Engine speed
|
Engine load
|
Throttle valve angle
|
Voltage value for throttle valve opening from throttle valve potentiometer
|
Specification1)
|
650...7502)
|
2.0...3.4
|
3.6...6.3
|
---
|
Display group 4
|
Display
|
xxxx rpm
|
xx.x ms
|
xxx km/h
|
xxxxxxxx
|
Indicated
|
Engine speed
|
Engine load
|
Speed
|
Operating condition3)
|
Specification1)
|
650...7502)
|
2.0...3.4
|
---
|
---
|
1)
The specifications must be attained when:
- engine runs at idling speed,
- the coolant temperature is at least 80 °C and
- electrical consumers are switched off
2)
Under the following conditions the idling speed is raised by the control unit:
- Battery voltage too low: up to 900 rpm
- After a long full throttle drive and at higher temperatures: up to 960 rpm
3)
Significance of numbers in 8 digit number block => Page 01-36
.
|
---|
|
Display zones
|
|
1
|
2
|
3
|
4
|
Display group 5
|
Display
|
xxxx rpm
|
xxx %
|
x.xx
|
x
|
Indicated
|
Engine speed
|
Activated charcoal filter solenoid valve 1 duty cycle
|
Activated charcoal filter solenoid valve 1 adaptation value
|
Activated charcoal filter solenoid valve 1 flushing rate
|
No specification for service departments
|
Display group 6
|
Display
|
x.xx
|
x.xx
|
x.x V
|
x.x V
|
Indicated
|
Mixture correction value
|
Mixture correction "learned" value
|
Throttle valve potentiometer voltage value for throttle valve opening
|
Value stored during basic setting for the throttle valve potentiometer position: Throttle valve closed
|
No specification for service departments
|
|
---|
|
Display zones
|
|
1
|
2
|
3
|
4
|
Display group 7 = Display group 1
|
|
Display group 8
|
Display
|
x.x V
|
x.x V
|
x.x V
|
x.x V
|
Indicated
|
Actual value from throttle valve potentiometer
|
Throttle valve emergency running profile
|
Throttle valve control unit min. stop
|
Throttle valve control unit max. stop
|
No specification for service departments
|
Display group 9
|
Display
|
x.xx
|
x.xx
|
x.xx V
|
x.xx
|
Indicated
|
Lambda integrator
|
Lambda adaptation
|
Lambda adaptation
|
Lambda adaptation
|
No specification for service departments
|
Significance of figures in 8 digit number block
|
---|
Significance when displayed digit = 1
|
x
|
x
|
x
|
x
|
x
|
x
|
x
|
x
|
Adjustment conditions (display group 1)
|
Operating condition (display group 4)
|
1
|
|
|
|
|
|
|
|
Fault in fault memory
|
Overrun
|
|
1
|
|
|
|
|
|
|
Not relevant
|
Idling speed
|
|
|
1
|
|
|
|
|
|
Not relevant
|
Part load (throttle)
|
|
|
|
1
|
|
|
|
|
Idling switch open
|
Full load
|
|
|
|
|
1
|
|
|
|
Fault in Lambda control
|
Acceleration enrichment
|
|
|
|
|
|
1
|
|
|
Throttle valve open
|
Weakening delayed
|
|
|
|
|
|
|
1
|
|
Speed above 2500 rpm
|
Not relevant
|
|
|
|
|
|
|
|
1
|
Coolant temperature below 80 °C
|
No. 1 cylinder recognized
|
|