Workshop Manuals Factory service & repair Volvo
01 Relays and Modules02 Sensors and Switches03 Maintenance04 Engine, Cooling and Exhaust05 Powertrain Management06 Transmission and Drivetrain07 Brakes and Traction Control08 Starting and Charging09 Power and Ground Distribution10 Steering and Suspension11 Heating and Air Conditioning12 Restraint Systems13 Accessories and Optional Equipment14 Body and Frame15 Cruise Control16 Instrument Panel, Gauges and Warning Indicators17 Lighting and Horns18 Windows and Glass19 Wiper and Washer Systems
Volvo XC90 FWD L6-3.2L VIN 98 B6324S (2007)01 · Relays and Modules
01 · Diagnostics

Electronic Brake Control Module: Diagrams (page 5 of 6)

Make
Volvo
Model
XC90 FWD
Engine
L6-3.2L VIN 98 B6324S
Year
2007
Section
Relays and Modules - Brakes and Traction Control › Electronic Brake Control Module
Relays and ModulesDiagrams · page 5 of 6
Electronic Brake Control Module: Diagrams (page 5 of 6) – Volvo XC90 FWD L6-3.2L VIN 98 B6324S (2007)

Remove the screws.
Use a 6 mm torx external socket.
Carefully pull the control module down so that the terminal pin on the control module comes loose inside the ABS modulator.
Continue pulling the control module down towards the brake lines and lift it out.

Installing the control module

Check:

-

the control module is correct (compare to the old one)

-

that none of the pins on the connector are damaged

-

that there are no contaminants on the mating surfaces between the control module and the ABS hydraulic modulator

-

that no parts of the old control module seals remain on the old ABS hydraulic modulator valves.

Position the control module on the brake lines.
Center the control module with the ABS modulator valves so that the terminal pins are correctly positioned in the modulator.
Press the control module up so that the terminal pins connect.

Install:

-

the screws. Tighten to 1.8 Nm.

-

the connector on the control module. Lock the connector.

Installing the integrated relay / fusebox

Install the box in its mounting.

Install:

-

the cable harness

-

the connector

-

the 2 screws in the mounting. Tighten to 10 Nm)

-

the 2 power supply cables

-

the nut for the mounting for the power supply cables.

Installing the air cleaner (ACL) housing

Press the air cleaner (ACL) housing into place.
Install the air hoses and the connector.

Finishing

Warning! No ABS, stability and traction control functions are available when there is communication with the Brake control module (BCM)
(Volvo Diagnostics are activated). ABS warning lamp flashes for as long as the diagnostics are activated. To cancel the diagnostics before test
driving the vehicle, the ignition must be switched off!

Pinch or Ctrl + scroll to zoom. Double-tap to reset.

The same page in: XC90 AWD L6-3.2L VIN 98 B6324S (2007), XC90 2.5T AWD L5-2.5L Turbo VIN 59 B5254T2 (2003), XC90 2.5T AWD L5-2.5L Turbo VIN 59 B5254T2 (2003), XC90 2.5T AWD L5-2.5L Turbo VIN 59 B5254T2 (2003), XC90 AWD L5-2.5L Turbo VIN 59 B5254T2 (2005), XC90 AWD L5-2.5L Turbo VIN 59 B5254T2 (2005), XC90 AWD L5-2.5L Turbo VIN 59 B5254T2 (2005), XC90 AWD L6-2.9L Turbo VIN 91 B6294T (2004), XC90 AWD L6-2.9L Turbo VIN 91 B6294T (2004), XC90 AWD L6-2.9L Turbo VIN 91 B6294T (2004), XC90 AWD L6-3.2L VIN 98 B6324S (2007), XC90 AWD L6-3.2L VIN 98 B6324S (2007), XC90 AWD V8-4.4L VIN 85 B8444S (2005).

Parts & tools for this job For 2007 Volvo XC90 3.2L

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.