| Diagnosis and Testing Special Tool(s) | | Hydraulic Pressure Gauge (0–60 bar) 307-201 | | | Adaptor for 301-201 307-201-01 | General Equipment Worldwide Diagnostic System (WDS) Ultraviolet fluid leak detection equipment The diagnosis by symptom index gives the technician diagnostic information, direction, and suggests possible components, using a symptom as a starting point. The diagnosis by symptom index is divided into two categories: - Electrical routines are indicated by 200 series numbers. The electrical routines list the possible electrical components that could cause or contribute to the symptom described.
- Hydraulic or mechanical routines are indicated by 300 series numbers. The hydraulic or mechanical routines list the possible hydraulic or mechanical components that could cause or contribute to the symptom described.
Diagnosis by Symptom Directions - Using the diagnosis by symptom index, select the concern or symptom that best describes the condition.
- Refer to the routine indicated in the diagnosis by symptom index.
- Always begin the diagnosis of a symptom with:
- Preliminary inspections.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
- Verifications of condition.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
- Checking the transmission fluid levels.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
-
NOTE:Not all concerns and conditions with electrical components will set a diagnostic trouble code (DTC). Be aware that the components listed may still be the cause. Verify the correct function of these components prior to proceeding to the hydraulic or mechanical routine listed. Begin with the electrical routine, if indicated. Follow the reference or action statements. Always carry out the on-board diagnostic tests as necessary. Never skip steps. If the concern is still present after electrical diagnosis, then proceed to the hydraulic or mechanical routine listed. - The hydraulic or mechanical routines list possible hydraulic or mechanical components that may cause the concern. These components are listed in the removal sequence and by the most probable cause. All components listed must be inspected to make sure of correct repair.
Diagnosis by Symptom Index | Engagement Concerns: | Routines | | | Electrical | Hydraulic or Mechanical | | No forward movement in "D" DRIVE only | 201A | 301A | | No forward movement only (all positions) | 201B | 301B | | No reverse movement only | 202 | 302 | | Harsh reverse movement only | 203 | 303 | | Harsh forward movement only | 204A | 304A | | Harsh manual 1st gear only | 204B | 304B | | Delayed or soft reverse movement only | 205 | 305 | | Delayed or soft forward movement only | 206 | 306 | | No forward movement and no reverse movement | 207 | 307 | | Harsh forward movement and harsh reverse movement | 208 | 308 | | Delayed or soft forward movement and delayed reverse movement | 209 | 309 | | Gearshift Concerns: | Routines | | | Electrical | Hydraulic or Mechanical | | Some or all shifts missing in "D" (DRIVE) only | 210 | 310 | | Gearshift timing concern - early or late | 211 | 311 | | Gearshift timing concern - erratic or hunting | 212 | 312 | | Gearshift feel - soft or slipping | 213 | 313 | | Gearshift feel - harsh | 214 | 314 | | No 1st gear in "D" (DRIVE), engages in a higher gear | 215 | 315 | | No manual 1st gear | 216 | 316 | | No manual 2nd gear | 217 | 317 | | No 1-2 upshift | 220 | 220 | | No 2-3 upshift | 221 | 321 | | No 3-4 upshift | 222 | 322 | | No 4-3 downshift | 223 | 323 | | No 3-2 downshift | 224 | 324 | | No 2-1 downshift | 225 | 325 | | Soft or slipping 1-2 upshift | 226 | 326 | | Soft or slipping 2-3 upshift | 227 | 327 | | Soft or slipping 3-4 upshift | 228 | 328 | | Soft or slipping 4-3 downshift | 229 | 329 | | Soft or slipping 3-2 downshift | 230 | 330 | | Soft or slipping 2-1 downshift | 231 | 331 | | Harsh 1-2 upshift | 232 | 332 | | Harsh 2-3 upshift | 233 | 333 | | Harsh 3-4 upshift | 234 | 334 | | Harsh 4-3 downshift | 235 | 335 | | Harsh 3-2 downshift | 236 | 336 | | Harsh 2-1 downshift | 237 | 337 | | Torque Converter Clutch Operation Concerns: | Routines | | | Electrical | Hydraulic or Mechanical | | Torque converter clutch does not apply | 240 | 340 | | Torque converter clutch always applied or stalls vehicle | 241 | 341 | | Torque converter clutch cycling, shudder or chatter | 242 | 342 | | Other Concerns: | Routines | | | Electrical | Hydraulic or Mechanical | | Selector lever efforts high | 251 | 351 | | External leaks from the transmission case | 252 | 352 | | Poor vehicle performance | 253 | 353 | | Noise or vibration - forward or reverse movement | 254 | 354 | | Engine will not crank | 255 | 355 | | No "P" (PARK) range | 256 | 356 | | Transmission overheating | 257 | 357 | | No engine braking in manual 1st gear | 259 | 359 | | Transmission fluid venting or foaming | 261 | 361 | | Transmission slips or chatters in manual 1st gear | 263 | 363 | | Transmission slips or chatters in manual 2nd gear | 264 | 364 | | Transmission slips or chatters in manual 3rd gear | 282 | 382 | | No engine braking in all gears | 283 | 383 | Diagnostic Routines | Possible Component | Reference or Action | | NO FORWARD MOVEMENT in "D" DRIVE ONLY: 201A - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harness, shift solenoid C (SSC) (off = low). | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | NO FORWARD MOVEMENT in "D" DRIVE ONLY: 301A - HYDRAULIC or MECHANICAL ROUTINE | | Transmission fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Transmission fluid condition. | Carry out the Transmission Fluid Condition Check.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the main control valve body.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL new component as necessary. | | Transmission Case | | | Transmission case damaged. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Possible Component | Reference or Action | | NO FORWARD MOVEMENT ONLY (ALL POSITIONS): 201B - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harness, shift solenoids (SSC, SSD, and SSE). | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | NO FORWARD MOVEMENT ONLY (ALL POSITIONS): 301B - HYDRAULIC or MECHANICAL ROUTINE | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Forward Planetary Assembly | | | Forward planetary assembly damaged. | Disassemble the forward planetary assembly.
REFER to: Planetary Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | One-Way Clutch | | | One-way clutch assembly worn, damaged or incorrectly assembled. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/Reverse Clutch | | | Low/reverse clutch balance piston or seals damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/reverse clutch friction elements damaged or worn. | | Low/reverse clutch return springs damaged. | | Possible Component | Reference or Action | | NO REVERSE MOVEMENT ONLY: 202 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harness, shift solenoids (SSC, SSD and SSE). | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | NO REVERSE MOVEMENT ONLY: 302 - HYDRAULIC or MECHANICAL ROUTINE | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Reverse Clutch | | | Reverse clutch balance piston or seals damaged. | Disassemble the reverse clutch.
REFER to: Reverse Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Reverse clutch friction elements damaged or worn. | | Reverse clutch return springs damaged. | | Low/Reverse Clutch | | | Low/reverse clutch balance piston or seals damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/reverse clutch friction elements damaged or worn. | | Low/reverse clutch return springs damaged. | | Possible Component | Reference or Action | | HARSH REVERSE MOVEMENT ONLY: 203 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harness or SSD. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | HARSH REVERSE MOVEMENT ONLY: 303 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Automatic Transmission Fluid Pressure | | | High transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Reverse Clutch | | | Reverse clutch balance piston or seals damaged. | Disassemble the reverse clutch.
REFER to: Reverse Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Reverse clutch friction elements damaged or worn. | | Reverse clutch return springs damaged. | | Low/Reverse Clutch | | | Low/reverse clutch balance piston or seals damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/reverse clutch friction elements damaged or worn. | | Low/reverse clutch return springs damaged. | | Possible Component | Reference or Action | | HARSH FORWARD MOVEMENT ONLY: 204A - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harness and SSC. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | HARSH FORWARD MOVEMENT ONLY: 304A - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Possible Component | Reference or Action | | HARSH MANUAL 1st GEAR ONLY: 204B - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harness and turbine shaft speed (TSS) sensor. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | HARSH MANUAL 1st GEAR ONLY: 304B - HYDRAULIC or MECHANICAL ROUTINE | | No Hydraulic or Mechanical Concerns. | | | Possible Component | Reference or Action | | DELAYED or SOFT REVERSE MOVEMENT ONLY: 205 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harness, SSD or EPC A. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | DELAYED or SOFT REVERSE MOVEMENT ONLY: 305 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | Low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Low/Reverse Clutch | | | Low/reverse clutch balance piston or seals damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/reverse clutch friction elements damaged or worn. | | Low/reverse clutch return springs damaged. | | Possible Component | Reference or Action | | DELAYED or SOFT FORWARD MOVEMENT ONLY: 206 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harness, SSC or PCA. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | DELAYED or SOFT FORWARD MOVEMENT ONLY: 306 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Possible Component | Reference or Action | | NO FORWARD MOVEMENT and NO REVERSE MOVEMENT: 207 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM or vehicle wiring harnesses (no electrical activity equals 3rd gear default). | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | NO FORWARD MOVEMENT and NO REVERSE MOVEMENT: 307 - HYDRAULIC or MECHANICAL ROUTINE | | Transmission Fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Transmission fluid condition. | Carry out the Transmission Fluid Condition Check.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Selector Lever Cable | | | Selector lever cable adjustment. | Adjust the selector lever cable.
REFER to: Selector Lever Cable Adjustment (307-05A Automatic Transmission/Transaxle External Controls - Vehicles With: 4-Speed Automatic Transmission (4F27E), General Procedures).
| | Selector lever cable damaged. | INSPECT the selector lever cable for visible signs of damage. REPAIR or INSTALL a new selector lever cable as necessary.
REFER to: Selector Lever Cable (307-05A Automatic Transmission/Transaxle External Controls - Vehicles With: 4-Speed Automatic Transmission (4F27E), Removal and Installation).
| | Transmission Range (TR) Sensor | | | TR sensor incorrectly aligned. | CHECK the TR sensor alignment and ADJUST if necessary.
REFER to: Transmission Range (TR) Sensor (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | TR sensor damaged. | INSPECT the TR sensor for visible signs of damage. INSTALL a new TR sensor as necessary.
REFER to: Transmission Range (TR) Sensor (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Turbine Shaft | | | Turbine shaft damaged. | Inspect for damage.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
REPAIR or INSTALL new components as necessary. | | Transmission Fluid Pump Assembly | | | Transmission fluid pump assembly retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Specifications (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Specifications).
| | Transmission fluid pump assembly seals damaged. | Disassemble the transmission fluid pump assembly.
REFER to: Pump Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Transmission fluid pump assembly channel(s) cross leaking or blocked. | | Rear Planetary Assembly | | | Rear planetary assembly damaged. | Disassemble the planetary assembly.
REFER to: Planetary Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Forward Planetary Assembly | | | Forward planetary assembly damaged. | Disassemble the planetary assembly.
REFER to: Planetary Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Final Drive Carrier and Differential Assembly | | | Final drive carrier and differential assembly damaged. | Disassemble the final drive carrier and differential assembly .
REFER to: Final Drive Carrier and Differential Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Torque Converter | | | Damaged torque converter flexplate or torque converter adapter plate. | CHECK the torque converter for damage.
REFER to: Torque Converter Diagnosis (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Damaged torque converter impeller. | | Damaged torque converter turbine. | | One-Way Clutch | | | One-way clutch worn, damaged or incorrectly assembled. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/Reverse Clutch | | | Low/reverse clutch balance piston or seals damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/reverse clutch friction elements damaged or worn. | | Low/reverse clutch return springs damaged. | | Possible Component | Reference or Action | | HARSH FORWARD MOVEMENT and HARSH REVERSE MOVEMENT: 208 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TR sensor, transmission fluid temperature (TFT) sensor, SSC and SSD. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | HARSH FORWARD MOVEMENT and HARSH REVERSE MOVEMENT: 308 - HYDRAULIC or MECHANICAL ROUTINE | | Transmission Fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Transmission fluid condition | Carry out the Transmission Fluid Condition Check.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Incorrect Transmission Fluid Pressure | | | High transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Reverse Clutch | | | Reverse clutch balance piston or seals damaged. | Disassemble the reverse clutch.
REFER to: Reverse Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Reverse clutch friction elements damaged or worn. | | Reverse clutch return springs damaged. | | Direct Clutch | | | Direct clutch balance piston or seals damaged. | Disassemble the direct clutch.
REFER to: Direct Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Direct clutch friction elements damaged or worn. | | Direct clutch return springs damaged. | | One-way Clutch | | | One-way clutch assembly worn, damaged or incorrectly assembled. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/Reverse Clutch | | | Low/reverse clutch seals, piston damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/reverse clutch friction elements damaged or worn. | | Low/reverse clutch return springs damaged. | | Possible Component | Reference or Action | | DELAYED or SOFT FORWARD MOVEMENT and DELAYED REVERSE MOVEMENT: 209 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TR sensor, TFT sensor, SSC and SSD. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | DELAYED or SOFT FORWARD MOVEMENT and DELAYED REVERSE MOVEMENT: 309 - HYDRAULIC or MECHANICAL ROUTINE | | Transmission Fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Transmission fluid condition. | Carry out the Transmission Fluid Condition Check.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Incorrect Transmission Fluid Pressure | | | High transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Transmission Fluid Pump Assembly | | | Transmission fluid pump assembly retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Specifications (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Specifications).
| | Transmission fluid pump assembly seals damaged. | Disassemble the transmission fluid pump assembly.
REFER to: Pump Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Transmission fluid pump assembly channel(s) cross leaking or blocked. | | Possible Component | Reference or Action | | SOME or ALL SHIFTS MISSING in "D" (DRIVE) ONLY: 210 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TR sensor, intake manifold air temperature (IAT) sensor, vehicle speed sensor (VSS) input, SSA, SSB, SSC, SSD SSE and pressure control solenoid (PCA). | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | SOME or ALL SHIFTS MISSING in "D" (DRIVE) ONLY: 310 - HYDRAULIC or MECHANICAL ROUTINE | | Some Shifts Missing ONLY | | | | If only some of the shifts are missing, determine which shift(s) is missing. Refer to the following routine(s) for further No Gearshift Concerns: | | | No 1-2 Upshift - Routine 220 or 320. | | | No 2-3 Upshift - Routine 221 or 321. | | | No 3-4 Upshift - Routine 222 or 322. | | | No 4-3 Downshift - Routine 223 or 323. | | | No 3-2 Downshift - Routine 224 or 324. | | | No 2-1 Downshift - Routine 225 or 325. | | Transmission Fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Transmission fluid condition. | Carry out the Transmission Fluid Condition Check.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Selector Lever Cable | | | Selector lever cable adjustment. | Adjust the selector lever cable.
REFER to: Selector Lever Cable Adjustment (307-05A Automatic Transmission/Transaxle External Controls - Vehicles With: 4-Speed Automatic Transmission (4F27E), General Procedures).
| | Selector lever cable damaged. | INSPECT the selector lever cable for visible signs of damage. REPAIR or INSTALL a new selector lever cable as necessary.
REFER to: Selector Lever Cable (307-05A Automatic Transmission/Transaxle External Controls - Vehicles With: 4-Speed Automatic Transmission (4F27E), Removal and Installation).
| | Transmission Range (TR) Sensor | | | TR sensor incorrectly aligned. | CHECK the TR sensor alignment and ADJUST as necessary.
REFER to: Transmission Range (TR) Sensor (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | TR sensor damaged. | INSPECT the TR sensor for visible signs of damage. INSTALL a new TR sensor as necessary.
REFER to: Transmission Range (TR) Sensor (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Transmission Fluid Pump Assembly | | | Transmission fluid pump assembly retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Specifications (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Specifications).
| | Transmission fluid pump assembly seals damaged. | Disassemble the transmission fluid pump assembly.
REFER to: Pump Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Transmission fluid pump assembly channel(s) cross leaking or blocked. | | Direct Clutch | | | Direct clutch balance piston or seals damaged. | Disassemble the direct clutch.
REFER to: Direct Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | | | Direct clutch friction elements damaged or worn. | | Direct clutch return springs damaged. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | One-way Clutch | | | One-way clutch worn, damaged or incorrectly assembled. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Possible Component | Reference or Action | | GEARSHIFT TIMING CONCERN - EARLY or LATE: 211 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, VSS, TSS sensor SSA, SSB, SSC, SSD, SSE and VFS. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | GEARSHIFT TIMING CONCERN - EARLY or LATE: 311 - HYDRAULIC or MECHANICAL ROUTINE | | Some Shifts Early or Late | | | | If only some of the shifts are early or late, determine which shift(s) are early or late. Refer to the following routine(s) for further Early or Late Gearshift Concerns: | | | Soft or Slipping 1-2 upshift - Routine 226 or 326. | | | Soft or Slipping 2-3 upshift - Routine 227 or 327. | | | Soft or Slipping 3-4 upshift - Routine 228 or 328. | | | Soft or Slipping 4-3 downhift - Routine 229 or 329. | | | Soft or Slipping 3-2 downshift - Routine 230 or 330. | | | Soft or Slipping 2-1 downshift - Routine 231 or 331. | | Transmission Fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Transmission fluid condition.. | Carry out the Transmission Fluid Condition Check.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Possible Component | Reference or Action | | GEARSHIFT TIMING CONCERN - ERRATIC or HUNTING: 212 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, VSS, IAT sensor. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | GEARSHIFT TIMING CONCERN - ERRATIC or HUNTING: 312 - HYDRAULIC or MECHANICAL ROUTINE | | Transmission Fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Transmission fluid condition. | Carry out the Transmission Fluid Condition Check.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Further Diagnosis | | | | Refer to the following routine(s) for further Timing Concerns: | | | No 1-2 upshift - Routine 220 or 330 | | | No 2-3 upshift - Routine 221 or 331 | | | No 3-4 upshift - Routine 222 or 332 | | | No 4-3 downshift - Routine 223 or 323 | | | No 3-2 downshift - Routine 224 or 324 | | | No 2-1 downshift - Routine 225 or 325 | | | Soft or slipping 1-2 upshift - Routine 226 or 326 | | | Soft or slipping 2-3 upshift - Routine 227 or 327 | | | Soft or slipping 3-4 upshift - Routine 228 or 328 | | | Soft or slipping 4-3 downshift - Routine 229 or 329 | | | Soft or slipping 3-2 downshift - Routine 230 or 330 | | | Soft or slipping 1-2 downshift - Routine 231 or 331 | | | Harsh 1-2 upshift - Routine 232 or 332 | | | Harsh 2-3 upshift - Routine 233 or 333 | | | Harsh 3-4 upshift - Routine 224 or 334 | | | Harsh 4-3 downshift - Routine 235 or 335 | | | Harsh 3-2 downshift - Routine 236 or 336 | | | Harsh 2-1 downshift - Routine 237 or 337 | | Possible Component | Reference or Action | | GEARSHIFT FEEL - SOFT or SLIPPING: 213 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TFT sensor, IAT sensor, VSS input SSA, SSB, SSC, SSD, SSE, VFS and PCA. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | GEARSHIFT FEEL - SOFT or SLIPPING: 313 - HYDRAULIC or MECHANICAL ROUTINE | | Some Shifts Soft or Slipping | | | | If only some of the shifts are soft or slipping, determine which shift(s) are soft or slipping. Refer to the following routine(s) for further Soft or Slipping Gearshift Concerns: | | | Soft or slipping 1-2 upshift - Routine 226 or 326 | | | Soft or slipping 2-3 upshift - Routine 227 or 327 | | | Soft or slipping 3-4 upshift - Routine 228 or 328 | | | Soft or slipping 4-3 downshift - Routine 229 or 329 | | | Soft or slipping 3-2 downshift - Routine 230 or 330 | | | Soft or slipping 2-1 downshift - Routine 231 or 331 | | Transmission Fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Transmission fluid condition. | Carry out the Transmission Fluid Condition Check.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Transmission Fluid Pump Assembly | | | Transmission fluid pump assembly retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Specifications (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Specifications).
| | Transmission fluid pump assembly seals damaged. | Disassemble the transmission fluid pump assembly.
REFER to: Pump Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Transmission fluid pump assembly channel(s) cross leaking or blocked. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL a new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Direct Clutch | | | Direct clutch balance piston or seals damaged. | Disassemble the direct clutch.
REFER to: Direct Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Direct clutch friction elements damaged or worn. | | Direct clutch return springs damaged. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Transmission Case | | | Transmission case damaged. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Possible Component | Reference or Action | | GEARSHIFT FEEL - HARSH: 214 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TR sensor, TFT sensor, IAT sensor, VSS input, SSA, SSB, SSC, SSD, SSE and PCA. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | GEARSHIFT FEEL - HARSH: 314 - HYDRAULIC or MECHANICAL ROUTINE | | Some Shifts Harsh | | | | If only some of the shifts are harsh, determine which shift(s) are harsh. Refer to the following routine(s) for further Harsh Gearshift Concerns: | | | Harsh 1-2 upshift - Routine 232 or 332 | | | Harsh 2-3 upshift - Routine 233 or 333 | | | Harsh 3-4 upshift - Routine 234 or 334 | | | Harsh 4-3 downshift - Routine 235 or 335 | | | Harsh 3-2 downshift - Routine 236 or 336 | | | Harsh 2-1 downshift - Routine 237 or 337 | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Turbine Shaft | | | Turbine shaft damaged. | Inspect for damage.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
REPAIR or INSTALL new components as necessary. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Final Drive Carrier and Differential Assembly | | | Final drive carrier and differential assembly damaged. | Disassemble the final drive carrier and differential assembly .
REFER to: Final Drive Carrier and Differential Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Transmission Case | | | Transmission case damaged. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Possible Component | Reference or Action | | NO 1st GEAR in "D" (DRIVE), ENGAGES in HIGHER GEAR: 215 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TR sensor and SSC. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | NO 1st GEAR in "D" (DRIVE), ENGAGES in HIGHER GEAR: 315 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | One-Way Clutch | | | One-way clutch worn, damaged or incorrectly assembled. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/Reverse Clutch | | | Low/reverse clutch balance piston or seals damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/reverse clutch friction elements damaged or worn. | | Low/reverse clutch return springs damaged. | | Possible Component | Reference or Action | | NO MANUAL 1st GEAR: 216 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM and vehicle wiring harnesses. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | NO MANUAL 1st GEAR: 316 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Low/Reverse Clutch | | | Low/reverse clutch balance piston or seals damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/reverse clutch friction elements damaged or worn. | | Low/reverse clutch return spring damaged. | | Planetary Assembly | | | Planetary assembly damaged. | Disassemble the planetary assembly.
REFER to: Planetary Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Possible Component | Reference or Action | | NO MANUAL 2nd GEAR: 217 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses and SSD. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | NO MANUAL 2nd GEAR: 317 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Direct Clutch | | | Direct clutch balance piston or seals damaged. | Disassemble the direct clutch.
REFER to: Direct Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Direct clutch friction elements damaged or worn. | | Direct clutch return springs damaged. | | One-way Clutch Assembly | | | One-way clutch worn, damaged or incorrectly assembled. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/Reverse Clutch | | | Low/reverse clutch balance piston or seals damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/reverse clutch friction elements damaged or worn. | | Low/reverse clutch return spring damaged. | | Possible Component | Reference or Action | | NO 1-2 UPSHIFT: 220 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, VSS, TR sensor, TSS sensor and SSD. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | NO 1-2 UPSHIFT: 320 - HYDRAULIC or MECHANICAL ROUTINE | | Transmission Fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Planetary Assembly | | | Planetary assembly damaged. | Disassemble the planetary assembly.
REFER to: Planetary Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Possible Component | Reference or Action | | NO 2-3 UPSHIFT: 221 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TR sensor, VSS, SSD and SSE. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | NO 2-3 UPSHIFT: 321 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Possible Component | Reference or Action | | NO 3-4 UPSHIFT: 222 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TR sensor, VSS, SSC and SSA. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | NO 3-4 UPSHIFT: 322 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Possible Component | Reference or Action | | NO 4-3 DOWNSHIFT: 223 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TR sensor, VSS, SSA and SSC. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | NO 4-3 DOWNSHIFT: 323 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Possible Component | Reference or Action | | NO 3-2 DOWNSHIFT: 224 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TR sensor, VSS and SSE. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | NO 3-2 DOWNSHIFT: 324 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Direct Clutch | | | Direct clutch balance piston or seals damaged. | Disassemble the direct clutch.
REFER to: Direct Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Direct clutch friction elements damaged or worn. | | Direct clutch return springs damaged. | | Possible Component | Reference or Action | | NO 2-1 DOWNSHIFT: 225 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TR sensor, VSS and SSD. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | NO 2-1 DOWNSHIFT: 325 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | One-way Clutch | | | One-way clutch worn, damaged or incorrectly assembled. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Possible Component | Reference or Action | | SOFT or SLIPPING 1-2 UPSHIFT: 226 - ELECTRICAL ROUTINE | | Incorrect Pressures | | | TCM, vehicle wiring harnesses, TSS sensor, VSS, TFT sensor and SSD. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | SOFT or SLIPPING 1-2 UPSHIFT: 326 - HYDRAULIC or MECHANICAL ROUTINE | | Transmission Fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Transmission fluid condition. | Carry out the Transmission Fluid Condition Check.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Possible Component | Reference or Action | | SOFT or SLIPPING 2-3 UPSHIFT: 227 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TSS sensor, TFT sensor and SSE. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | SOFT or SLIPPING 2-3 UPSHIFT: 327 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Direct Clutch | | | Direct clutch balance piston or seals damaged. | Disassemble the direct clutch.
REFER to: Direct Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Direct clutch friction elements damaged or worn. | | Direct clutch return springs damaged. | | Possible Component | Reference or Action | | SOFT or SLIPPING 3-4 UPSHIFT: 228 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, SSA, SSC, vehicle wiring harnesses and TFT sensor. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | SOFT or SLIPPING 3-4 UPSHIFT: 328 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Possible Component | Reference or Action | | SOFT or SLIPPING 4-3 DOWNSHIFT: 229 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TFT sensor, SSA and SSC. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | SOFT or SLIPPING 4-3 DOWNSHIFT: 329 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Possible Component | Reference or Action | | SOFT or SLIPPING 3-2 DOWNSHIFT: 230 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TFT sensor and SSE. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | SOFT or SLIPPING 3-2 DOWNSHIFT: 330 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Possible Component | Reference or Action | | SOFT or SLIPPING 2-1 DOWNSHIFT: 231 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, SSD, VSS, TSS, TR sensor, vehicle wiring harnesses and TFT sensor. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | SOFT or SLIPPING 2-1 DOWNSHIFT: 331 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Possible Component | Reference or Action | | HARSH 1-2 UPSHIFT: 232 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TSS sensor, TR sensor, TFT sensor and SSD. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | HARSH 1-2 UPSHIFT: 332 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Possible Component | Reference or Action | | HARSH 2-3 UPSHIFT: 233 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TSS sensor, TR sensor, TFT sensor and SSE. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | HARSH 2-3 UPSHIFT: 333 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Direct Clutch | | | Direct clutch balance piston or seals damaged. | Disassemble the direct clutch.
REFER to: Direct Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Direct clutch friction elements damaged or worn. | | Direct clutch return springs damaged. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Possible Component | Reference or Action | | HARSH 3-4 UPSHIFT: 234 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TR sensor, TFT sensor, SSA and SSC. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | HARSH 3-4 UPSHIFT: 334 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Direct Clutch | | | Direct clutch balance piston or seals damaged. | Disassemble the direct clutch.
REFER to: Direct Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Direct clutch friction elements damaged or worn. | | Direct clutch return springs damaged. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Possible Component | Reference or Action | | HARSH 4-3 DOWNSHIFT: 235 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TR sensor, TFT sensor, SSA and SSC. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | HARSH 4-3 DOWNSHIFT: 335 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Possible Component | Reference or Action | | HARSH 3-2 DOWNSHIFT: 236 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TSS sensor, TR sensor, TFT sensor and SSE. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | HARSH 3-2 DOWNSHIFT: 336 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Direct Clutch | | | Direct clutch balance piston or seals damaged. | Disassemble the direct clutch.
REFER to: Direct Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Direct clutch friction elements damaged or worn. | | Direct clutch return springs damaged. | | Possible Component | Reference or Action | | HARSH 2-1 DOWNSHIFT: 237 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TSS sensor, TR sensor, TFT sensor, VFS and SSD. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | HARSH 2-1 DOWNSHIFT: 337 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | One-Way Clutch | | | One-way clutch worn, damaged or incorrectly assembled. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Possible Component | Reference or Action | | TORQUE CONVERTER CLUTCH DOES NOT APPLY: 240 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TFT sensor, SSB and SSC. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | TORQUE CONVERTER CLUTCH DOES NOT APPLY: 340 - HYDRAULIC or MECHANICAL ROUTINE | | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Transmission Fluid Pump Assembly | | | Transmission fluid pump assembly retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Specifications (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Specifications).
| | Transmission fluid pump assembly seals damaged. | Disassemble the transmission fluid pump assembly.
REFER to: Pump Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Transmission fluid pump assembly channel(s) cross leaking or blocked. | | Torque Converter Assembly | | | Damaged torque converter flexplate or torque converter adapter plate. | CHECK the torque converter for damage.
REFER to: Torque Converter Diagnosis (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Damaged torque converter impeller. | | Damaged torque converter turbine. | | Possible Component | Reference or Action | | TORQUE CONVERTER CLUTCH ALWAYS APPLIED or STALLS VEHICLE: 241 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, SSC and SSB. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | TORQUE CONVERTER CLUTCH ALWAYS APPLIED or STALLS VEHICLE: 341 - HYDRAULIC or MECHANICAL ROUTINE | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | One-Way Clutch | | | One-way clutch worn, damaged or incorrectly assembled. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/Reverse Clutch | | | Low/reverse clutch balance piston or seals damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/reverse clutch friction elements damaged or worn. | | Low/reverse clutch return springs damaged. | | Torque Converter | | | Damaged torque converter flexplate or torque converter adapter plate. | CHECK the torque converter for damage.
REFER to: Torque Converter Diagnosis (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Damaged torque converter impeller. | | Damaged torque converter turbine. | | Possible Component | Reference or Action | | TORQUE CONVERTER CLUTCH CYCLING, SHUDDER or CHATTER: 242 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, SSB and SSC. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | TORQUE CONVERTER CLUTCH CYCLING, SHUDDER or CHATTER: 342 - HYDRAULIC or MECHANICAL ROUTINE | | Transmission Fluid | | | Transmission fluid condition.. | Carry out the Transmission Fluid Condition Check.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Torque Converter Assembly | | | Damaged torque converter flexplate or torque converter adapter plate. | CHECK the torque converter for damage.
REFER to: Torque Converter Diagnosis (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Damaged torque converter impeller. | | Damaged torque converter turbine. | | Possible Component | Reference or Action | | SELECTOR LEVER EFFORTS HIGH: 251 - ELECTRICAL ROUTINE | | Transmission Control System | | | TR sensor. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | SELECTOR LEVER EFFORTS HIGH: 351 - HYDRAULIC or MECHANICAL ROUTINE | | Selector Lever Cable | | | Selector lever cable adjustment. | Adjust the selector lever cable.
REFER to: Selector Lever Cable Adjustment (307-05A Automatic Transmission/Transaxle External Controls - Vehicles With: 4-Speed Automatic Transmission (4F27E), General Procedures).
| | Selector lever cable damaged. | INSPECT the selector lever cable for visible signs of damage. REPAIR or INSTALL a new selector lever cable as necessary.
REFER to: Selector Lever Cable (307-05A Automatic Transmission/Transaxle External Controls - Vehicles With: 4-Speed Automatic Transmission (4F27E), Removal and Installation).
| | Transmission Range (TR) Sensor | | | TR sensor incorrectly aligned. | CHECK the TR sensor alignment and ADJUST as necessary.
REFER to: Transmission Range (TR) Sensor (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | TR sensor damaged. | INSPECT the TR sensor for visible signs of damage. INSTALL a new TR sensor as necessary.
REFER to: Transmission Range (TR) Sensor (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Transmission Case | | | Selector lever damaged. | INSPECT the selector lever for visible signs of damage. INSTALL a new selector lever as necessary.
REFER to: Selector Lever Assembly (307-05A Automatic Transmission/Transaxle External Controls - Vehicles With: 4-Speed Automatic Transmission (4F27E), Removal and Installation).
| | Selector lever shaft damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Selector lever shaft retaining pin damaged. | | Possible Component | Reference or Action | | EXTERNAL LEAKS FROM the TRANSMISSION CASE: 252 - ELECTRICAL ROUTINE | | Transmission Control System | | | VSS, TSS and TR sensors. | Inspect for leakage. If areas around VSS or TSS sensors show signs of leakage, install a new sensor O-ring seal. If area behind TR sensor shows signs of leakage, install a new selector lever shaft seal. | | EXTERNAL LEAKS FROM the TRANSMISSION CASE: 352 - HYDRAULIC or MECHANICAL ROUTINE | | Transmission Fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Transmission Case | | | Transmission case vent tube damaged. | INSPECT the transmission case vent tube for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Transmission Case Seals and Gaskets | | | Fluid leakage at transmission case seals and gaskets. | Inspect for fluid leakage.
REFER to: Leakage Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Possible Component | Reference or Action | | POOR VEHICLE PERFORMANCE: 253 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, VSS, TSS sensor, TFT sensor, TR sensor, SSA, SSB, SSC, SSD, SSE and PCA. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | POOR VEHICLE PERFORMANCE: 353 - HYDRAULIC or MECHANICAL ROUTINE | | Transmission Fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Turbine Shaft | | | Turbine shaft damaged. | INSPECT the turbine shaft for visible signs of damage.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
REPAIR or INSTALL new components as necessary. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Torque Converter | | | Damaged torque converter flexplate or torque converter adapter plate. | CHECK the torque converter for damage.
REFER to: Torque Converter Diagnosis (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Damaged torque converter impeller. | | Damaged torque converter turbine. | | One-Way Clutch | | | One-way clutch worn, damaged or incorrectly assembled. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Possible Component | Reference or Action | | NOISE or VIBRATION - FORWARD or REVERSE MOVEMENT: 254 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, SSA, SSB, SSC, SSD, SSE and PCA. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | NOISE or VIBRATION - FORWARD or REVERSE MOVEMENT: 354 - HYDRAULIC or MECHANICAL ROUTINE | | Transmission Fluid Pump Assembly | | | Transmission fluid pump assembly retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Specifications (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Specifications).
| | Transmission fluid pump assembly seals damaged. | Disassemble the transmission fluid pump assembly.
REFER to: Pump Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Transmission fluid pump assembly channel(s) cross leaking or blocked. | | Flexplate | | | Flexplate damaged. | INSPECT the flexplate for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Possible Component | Reference or Action | | ENGINE WILL NOT CRANK: 255 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses and TR sensor. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | ENGINE WILL NOT CRANK: 355 - HYDRAULIC or MECHANICAL ROUTINE | | Selector Lever Cable | | | Selector lever cable adjustment. | Adjust the selector lever cable.
REFER to: Selector Lever Cable Adjustment (307-05A Automatic Transmission/Transaxle External Controls - Vehicles With: 4-Speed Automatic Transmission (4F27E), General Procedures).
| | Selector lever cable damaged. | INSPECT the selector lever cable for visible signs of damage. REPAIR or INSTALL a new selector lever cable as necessary.
REFER to: Selector Lever Cable (307-05A Automatic Transmission/Transaxle External Controls - Vehicles With: 4-Speed Automatic Transmission (4F27E), Removal and Installation).
| | Transmission Range (TR) Sensor | | | TR sensor incorrectly aligned. | CHECK the TR sensor alignment and ADJUST as necessary.
REFER to: Transmission Range (TR) Sensor (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | TR sensor damaged. | INSPECT the TR sensor for visible signs of damage. INSTALL a new TR sensor as necessary.
REFER to: Transmission Range (TR) Sensor (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Flexplate | | | Flexplate damaged. | INSPECT the flexplate for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Possible Component | Reference or Action | | NO "P" (PARK) RANGE: 256 - ELECTRICAL ROUTINE | | Transmission Control System | | | No electrical concerns. | | | NO "P" (PARK) RANGE: 356 - HYDRAULIC or MECHANICAL ROUTINE | | Selector Lever Cable | | | Selector lever cable adjustment. | Adjust the selector lever cable.
REFER to: Selector Lever Cable Adjustment (307-05A Automatic Transmission/Transaxle External Controls - Vehicles With: 4-Speed Automatic Transmission (4F27E), General Procedures).
| | Selector lever cable damaged. | INSPECT the selector lever cable for visible signs of damage. REPAIR or INSTALL a new selector lever cable as necessary.
REFER to: Selector Lever Cable (307-05A Automatic Transmission/Transaxle External Controls - Vehicles With: 4-Speed Automatic Transmission (4F27E), Removal and Installation).
| | Transmission Range (TR) Sensor | | | TR sensor incorrectly aligned. | CHECK the TR sensor alignment and ADJUST as necessary.
REFER to: Transmission Range (TR) Sensor (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | TR sensor damaged. | INSPECT the TR sensor for visible signs of damage. INSTALL a new TR sensor as necessary.
REFER to: Transmission Range (TR) Sensor (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Transmission Case | | | Selector lever damaged. | INSPECT the selector lever for visible signs of damage. INSTALL a new selector lever as necessary.
REFER to: Selector Lever Assembly (307-05A Automatic Transmission/Transaxle External Controls - Vehicles With: 4-Speed Automatic Transmission (4F27E), Removal and Installation).
| | Selector lever shaft damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Selector lever shaft retaining pin damaged. | | Transmission Park Assembly | | | Transmission park assembly damaged or incorrectly assembled. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Possible Component | Reference or Action | | TRANSMISSION OVERHEATING: 257 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses, TFT sensor and SSB. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | TRANSMISSION OVERHEATING: 357 - HYDRAULIC or MECHANICAL ROUTINE | | Transmission Fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Transmission Fluid Pump Assembly | | | Transmission fluid pump assembly retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Specifications (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Specifications).
| | Transmission fluid pump assembly seals damaged. | Disassemble the transmission fluid pump assembly.
REFER to: Pump Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Transmission fluid pump assembly channel(s) cross leaking or blocked. | | Transmission Case | | | Transmission case vent tube damaged. | INSPECT the transmission case vent tube for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Torque Converter | | | Damaged torque converter flexplate or torque converter adapter plate. | CHECK the torque converter for damage.
REFER to: Torque Converter Diagnosis (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Damaged torque converter impeller. | | Damaged torque converter turbine. | | Other | | | Restriction in the transmission cooling system. | CHECK the transmission cooling system for damage.
REFER to: Transaxle Cooling (307-02A Transmission/Transaxle Cooling - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Excessive trailer tow load. | REFER to the relevant section of the owner literature for specifications on trailer towing. | | Poor engine performance. | Check the engine performance.
REFER to: Engine (303-00 Engine System - General Information, Diagnosis and Testing).
| | Possible Component | Reference or Action | | NO ENGINE BRAKING IN MANUAL 1st GEAR: 259 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses and SSD. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | NO ENGINE BRAKING IN MANUAL 1st GEAR: 359 - HYDRAULIC or MECHANICAL ROUTINE | | Transmission Fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Transmission Fluid Pump Assembly | | | Transmission fluid pump assembly retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Specifications (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Specifications).
| | Transmission fluid pump assembly seals damaged. | Disassemble the transmission fluid pump assembly.
REFER to: Pump Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Transmission fluid pump assembly channel(s) cross leaking or blocked. | | Low/Reverse Clutch | | | Low/reverse clutch balance piston or seals damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/reverse clutch friction elements damaged or worn. | | Low/reverse clutch return springs damaged. | | Possible Component | Reference or Action | | TRANSMISSION FLUID VENTING or FOAMING: 261 - ELECTRICAL ROUTINE | | Transmission Control System | | | No electrical concerns. | | | TRANSMISSION FLUID VENTING or FOAMING: 361 - HYDRAULIC or MECHANICAL ROUTINE | | Transmission Fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Transmission fluid condition.. | Carry out the Transmission Fluid Condition Check.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Transmission Fluid Pump Assembly | | | Transmission fluid pump assembly retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Specifications (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Specifications).
| | Transmission fluid pump assembly seals damaged. | Disassemble the transmission fluid pump assembly.
REFER to: Pump Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Transmission fluid pump assembly channel(s) cross leaking or blocked. | | Transmission Case | | | Transmission case vent tube damaged. | INSPECT the transmission case vent tube for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Other | | | | Refer to the following routine(s) for further Other Concerns: | | Transmission overheating - Routine 257 or 357 | | Possible Component | Reference or Action | | TRANSMISSION SLIPS or CHATTERS IN MANUAL 1st GEAR: 263 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses and SSC. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | TRANSMISSION SLIPS or CHATTERS IN MANUAL 1st GEAR: 363 - HYDRAULIC or MECHANICAL ROUTINE | | Transmission Fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Transmission fluid condition.. | Carry out the Transmission Fluid Condition Check.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Main Control Valve Body | | | Main control valve body retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Main Controls (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), In-vehicle Repair).
| | Main control valve body separator plate damaged. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Main control valve body contaminated. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of contamination. REPAIR or INSTALL new components as necessary. | | Main control valve body valves or springs damaged, incorrectly assembled, missing or stuck. | Disassemble the main control valve body.
REFER to: Main Control Valve Body (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. DO NOT stone, file or sand the valves. This will remove the anodized finish and may result in further main control valve body or transmission damage. | | Transmission Fluid Pump Assembly | | | Transmission fluid pump assembly retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Specifications (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Specifications).
| | Transmission fluid pump assembly seals damaged. | Disassemble the transmission fluid pump assembly.
REFER to: Pump Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Transmission fluid pump assembly channel(s) cross leaking or blocked. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | One-Way Clutch | | | One-way clutch worn, damaged or incorrectly assembled. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/Reverse Clutch | | | Low/reverse clutch balance piston or seals damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Low/reverse clutch friction elements damaged or worn. | | Low/reverse clutch return springs damaged. | | Possible Component | Reference or Action | | TRANSMISSION SLIPS or CHATTERS IN MANUAL 2nd GEAR: 264 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses and SSD. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | TRANSMISSION SLIPS or CHATTERS IN MANUAL 2nd GEAR: 364 - HYDRAULIC or MECHANICAL ROUTINE | | Transmission Fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Transmission fluid condition.. | Carry out the Transmission Fluid Condition Check.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Transmission Fluid Pump Assembly | | | Transmission fluid pump assembly retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Specifications (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Specifications).
| | Transmission fluid pump assembly seals damaged. | Disassemble the transmission fluid pump assembly.
REFER to: Pump Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Transmission fluid pump assembly channel(s) cross leaking or blocked. | | Intermediate and Overdrive Brake Band Servo | | | Intermediate and overdrive brake band servo seal(s) damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band servo piston damaged. | | Intermediate and overdrive brake band servo piston spring damaged. | | Intermediate and Overdrive Brake Band | | | Intermediate and overdrive brake band damaged. | Disassemble the transmission.
REFER to: Transaxle (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Disassembly).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Intermediate and overdrive brake band anchor bolt damaged or worn. | INSPECT for visible signs of damage. REPAIR or INSTALL a new component as necessary. | | Planetary Assembly | | | Planetary assembly damaged. | Disassemble the planetary assembly.
REFER to: Planetary Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | Possible Component | Reference or Action | | TRANSMISSION SLIPS or CHATTERS IN MANUAL 3rd GEAR: 282 - ELECTRICAL ROUTINE | | Transmission Control System | | | No electrical concerns. | | | TRANSMISSION SLIPS or CHATTERS IN MANUAL 3rd GEAR: 382 - HYDRAULIC or MECHANICAL ROUTINE | | Transmission Fluid | | | Incorrect transmission fluid level. | Adjust the transmission fluid to the correct level.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Transmission fluid condition. | Carry out the Transmission Fluid Condition Check.
REFER to: Preliminary Inspection (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
| | Incorrect Transmission Fluid Pressure | | | High or low transmission fluid pressure. | Carry out the Line Pressure Test.
REFER to: Special Testing Procedures (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Diagnosis and Testing).
REPAIR or INSTALL new components as necessary. | | Transmission Fluid Pump Assembly | | | Transmission fluid pump assembly retaining bolts not tightened to specification. | Tighten to specification.
REFER to: Specifications (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), Specifications).
| | Transmission fluid pump assembly seals damaged. | Disassemble the transmission fluid pump assembly.
REFER to: Pump Assembly (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
Inspect for damage. REPAIR or INSTALL new components as necessary. | | Transmission fluid pump assembly channel(s) cross leaking or blocked. | | Forward Clutch | | | Forward clutch balance piston or seals damaged. | Disassemble the forward clutch.
REFER to: Forward Clutch (307-01A Automatic Transmission/Transaxle - Vehicles With: 4-Speed Automatic Transmission (4F27E), ).
INSPECT for visible signs of damage. REPAIR or INSTALL new components as necessary. | | Forward clutch friction elements damaged or worn. | | Forward clutch return springs damaged. | | | Reference or Action | | NO ENGINE BRAKING IN ALL GEARS: 283 - ELECTRICAL ROUTINE | | Transmission Control System | | | TCM, vehicle wiring harnesses and SSD. | Carry out the WDS quick test. REFER to WDS. REPAIR or INSTALL new components as necessary. Clear the DTCs. Carry out a road test and TEST the system for normal operation. | | NO ENGINE BRAKING IN ALL GEARS: 383 - HYDRAULIC or MECHANICAL ROUTINE | | No Hydraulic or Mechanical concerns. | | | |
/Description and Operation/Diagnosis and Testing//img/17033.jpg)
/Description and Operation/Diagnosis and Testing//img/E48050.jpg)
