- Corsa B Workshop Manual
- General Vehicle Information
- A Maintenance, Body and Chassis Sheet Metal Parts, Frame
- B Paint
- C Body Equipment
- D Heating, Ventilation, Air Conditioning (HVAC)
- E Front Wheel Suspension, Wheels and Tyres
- F Rear Axle and Rear Wheel Suspension
- H Brakes
- J Engine and Engine Aggregates
- Repair Instructions
- Specifications
- Labour Time Allowances
- Diagnostic Information and Procedures
- Other Information
- Technical Service Bulletins
- Technical Information
- OHC Petrol Engine
- DOHC Petrol Engine
- Diesel Engine
- Fuel Injection Systems
- Technical Service Bulletins
- Mechanical Fuel Injection System (Diesel Engine)
- Multec (1.2l / 1.4l)
- Multec M
- Multec SZ
- Multec S
- Repair Instructions
- Intake Manifold - Upper Part, Remove and Install (X 14 XE, C 14 SEL, X 16 XE, C 16 SEL)
- Intake Manifold - Lower Part, Remove and Install (X 14 XE, C 14 SEL, X 16 XE, C 16 SEL)
- Throttle Body, Remove and Install (X 14 XE, C 14 SEL, X 16 XE, C 16 SEL) XE, C 16 SEL)
- Fuel Pump Relay, Remove and Install reinstallation
- Fuel Pressure Regulator, Remove and Install
- Injectors, Remove and Install (X 14 XE, C 14 SEL, X 16 XE, C 16 SEL)
- Coolant Temperature Sensor, Remove and Install
- Pressure Sensor - Intake Pipe, Remove and Install (X 14 XE, C 14 SEL, X 16 XE, C 16 SEL)
- Intake Air Temperature Sensor, Remove and Install (X14XE, C14SEL, X16XE, C16SEL)
- Inductive Pulse Pick-up, Remove and Install
- Camshaft Pulse Pick-up, Remove and Install
- Knock Sensor, Remove and Install
- Oxygen Sensor, Remove and Install
- DIS Ignition Module, Remove and Install reinstallation
- Control Unit, Remove and Install
- Program Memory in Control Unit, Knock Module in Control Unit or Control Unit, Replace (up to MY '96 1/2)". 1996 1/2)
- Immobiliser with Transponder as of MY '96 Immobiliser Control Unit, Remove and Install
- Important Workshop Instructions
- Throttle Valve Potentiometer, Remove and Install
- Idle Speed Stepper Motor, Remove and Install
- Fuel Pressure, Check
- Tank Vent Valve, Remove and Install reinstallation
- Reference Gap Between Inductive Pulse Pick-up and Increment Disc, Measure
- Illustration: Air Ducts (X 14 XE, C 14 SEL, X 16 XE, C 16 SEL)
- Component Locator
- Specifications
- Special Tools and Equipment
- Warnings, Disclaimers, Safety
- Labour Time Allowances
- Diagnostic Information and Procedures
- Other Information
- Technical Service Bulletins
- Technical Information
- Throttle Valve Housing
- Throttle Valve Potentiometer
- Intake Pipe Pressure Sensor
- Pressure Regulator
- Injection Valve
- Inductive Impulse Sensor
- Knocking Sensor
- Fuel Pump
- Fuel Pump Relay
- Oxygen Sensor
- Idle Air Control Stepper Motor
- Air Mass Meter
- Control Unit
- Tank Ventilation Valve
- Coolant Temperature Sensor
- Odometer Frequency Sensor
- DIS-Ignition Module
- Ignition leads/connectors
- Wiring Harness
- Engine Electrics
- Cooling System
- Turbo-Charging
- K Clutch and Transmission
- L Fuel and Exhaust System
- M Steering
- N Electrical Equipment and Instruments
- R Accessories