|
Special tools (X16XEL, Y16XE, Z16XE, X18XE1,
Z18XE, Z18XEL)
|
|
Special tools (X 16 XEL, Y 16 XE, Z 16 XE, X 18
XE1, Z 18 XE, Z 18 XEL)
|
KM-135
|
Adapter
|
|
To measure engine oil pressure in conjunction with KM-498-B
|
|
KM-194-E
|
Spark Plug Wrench
|
|
To remove/install spark plug
|
|
KM-301
|
Gauge Bar
|
|
To check piston projection
|
|
KM-340-F
|
Valve Cutter Set
|
|
To cut, correct the valve seats
|
|
KM-348
|
Valve Spring Compressor
|
|
To press the valve springs together in conjunction with
KM-653-A
|
|
KM-412
|
Engine Overhaul Stand
|
|
To hold the removed engine
|
|
|
|
|
KM-412-3
|
Adapter
|
|
To hold engine in conjunction with KM-412
|
|
KM-417
|
Assembly Sleeves (X 16 XEL)
|
|
To press the crankshaft seal ring in the oil pump housing
|
|
KM-422
|
Installer
|
|
To press the seal ring in the camshaft
|
|
KM-470-B
|
Angular Torque Wrench
|
|
To tighten cylinder head bolts
|
|
KM-471
|
Adapter
|
|
To check the pressurised cooling system in conjunction with the
coolant tester
|
|
KM-498-B
|
Oil Pressure Manometer
|
|
To check engine oil pressure in conjunction with KM-135
|
|
|
|
|
MKM-571-B
|
Dial Gauge
|
|
To check various components
|
|
MKM-596-A
|
Temperature Gauge
|
|
To measure oil temperature
|
|
MKM-604-D
|
Torx Bit and Socket Set
|
|
To remove/install the Torx bolts
|
|
KM-609
|
Electronic-Kit
|
|
To diagnose electrical and electronic systems
|
|
MKM-610
|
Torque Wrench, 1/2"
|
|
Measuring range 30-130 Nm
|
|
MKM-611
|
Torque Wrench, 3/8"
|
|
Measuring range 10-60 Nm
|
|
|
|
|
KM-652
|
Flywheel/Drive Disc Holder
|
|
To lock flywheel or drive disc
|
|
KM-653-A
|
Adapter
|
|
To tension the valve springs in conjunction with KM-348
|
|
KM-658
|
Installer
|
|
To install crankshaft rear seal ring
|
|
MKM-667
|
Pressure and Vacuum Pump
|
|
To check for leaks in vacuum unit
|
|
MKM-669
|
Torque Wrench, 1/2"
|
|
Measuring range 50-300 Nm
|
|
KM-726-A
|
Oil Filter Wrench
|
|
To remove/install the oil filter
|
|
|
|
|
KM-728
|
Remover/Installer
|
|
To remove/install the knock sensor
|
|
KM-796
|
Remover
|
|
To open quick-release fittings for fuel system
|
|
KM-805
|
Reamer (6 mm)
|
|
To ream the valve guides (oversize 0.075 mm)
|
|
KM-835-A
|
Installer
|
|
To install the valve stem seals (6 mm)
|
|
KM-836
|
Remover
|
|
To remove the spark plug connector
|
|
KM-840
|
Remover
|
|
To remove valve stem seals
|
|
|
|
|
KM-845
|
Suction Device
|
|
To remove the hydraulic valve lifters
|
|
KM-852
|
Locking/Fixing Tool
|
|
To lock the camshaft pulleys
|
|
MKM-883-1
|
Engine Bridge
|
|
To hold/lift the engine
|
|
MKM-883-2
|
Adapter Plate
|
|
To align the engine in conjunction with MKM-883-1
|
|
MKM-889
|
Remover/Installer
|
|
To remove/install the valve stem seals (cylinder head
installed)
|
|
KM-904
|
Base Frame
|
|
To remove and install various vehicle components with additional
adapters
|
|
|
|
|
KM-905
|
Centring Support
|
|
To remove/install the front axle body in conjunction with
KM-904
|
|
KM-911
|
Flywheel Locking Device
|
|
To hold the flywheel/drive disc
|
|
KM-913-A
|
Installation Wrench
|
|
To tension/slacken the V-ribbed belt tensioning pulley
|
|
KM-956-1
|
Handle
|
|
Holding camshaft timing gears to loosen/tighten bolts in
conjunction with KM-6347
|
|
KM-961
|
Reamer, 5 mm (X 18 XE1)
|
|
To ream the valve guides, oversize 0.075 mm
|
|
KM-6009
|
Remover/Installer
|
|
To remove/install the ignition module
|
|
|
|
|
KM-6010
|
Assembly Sleeves (X 18 XE1)
|
|
To press the crankshaft seal ring in the oil pump housing
|
|
KM-6129
|
Remover/Installer
|
|
To remove/install the lambda sensors
|
|
KM-6173
|
Engine Mount
|
|
To attach engine to front axle body
|
|
KM-6347
|
Bracket
|
|
Holding camshaft timing gears to loosen/tighten bolts in
conjunction with KM-956-1
|
|
KM-J-34730-91
|
Pressure Tester
|
|
To check fuel pressure
|
|
|
|
