FRONT OIL SEAL OF R/H OVERHEAD CAMSHAFTS - REPLACE

Operation 1036E58 · CAMSHAFTS (2) IN CYLINDER HEADS (2)

3.2 V6

Removing

Position the vehicle on the ramp

Proceed with removal

Op. 4450B04 RIGHT FRONT WHEEL R R

Proceed with removal

Proceed with removal

Op. 7055B64 LH OR RH REFLECTOR(ONE) ON REAR BUMPERS - R R

Proceed with removal

Proceed with removal

Op. 1092G10 SINGLE ENGINE BELT R R

Proceed with removal

Proceed with removal

Op. 1092A10 CRANKSHAFT SERVICES PULLEY - R.R.

Proceed with removal

Proceed with removal

Op. 1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R + R

Proceed with removal

Proceed with removal

Op. 1016A42 LEFT HAND CYLINDER HEAD IGNITION COIL COVER - R+R

Proceed with removal

Proceed with removal

Op. 5510C16 LEFT HAND CYLINDER HEAD IGNITION COIL - R+R

Proceed with removal

1. Undo the bolts (1a) and remove the right cylinder head camshaft front caps (1b).

Op. 1016A30 LEFT CAM COVER - R + R AND REPLACE GASKET

2. Release and remove the oil seals for the right cylinder head camshafts.

Op. 1072B50 SLEEVES CONNECTING AIR CAPACITY BOX TO INLET MANIFOLD IS - R+R

Op. 5510C18 RIGHT HAND CYLINDER HEAD IGNITION COIL - R+R

Op. 1016A34 RIGHT-HAND CAM COVER - R + R AND REPLACE GASKET

Op. 1032B10 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT

Op. 1032B58 RIGHT CYLINDER HEAD DRIVEN TOOTHED PULLEYS - R.R.

Op. 1008C14 ENGINE LINK BRACKET - R R

Refitting

Place the camshaft front caps back in their housings in the right cylinder head following the sequence shown in the diagram.

Tighten the bolts fixing the right cylinder head camshaft front caps to the recommended torque.

1. Fit the camshaft front oil seals (1a) using the tool (1b).

Proceed with refitting

Op. 1008C14 ENGINE LINK BRACKET - R R.

Proceed with refitting

Op. 1032B58 RIGHT CYLINDER HEAD DRIVEN TOOTHED PULLEYS - R.R..

Proceed with refitting

Op. 1032B10 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT.

Proceed with refitting

Op. 1016A34 RIGHT-HAND CAM COVER - R + R AND REPLACE GASKET.

Proceed with refitting

Op. 5510C18 RIGHT HAND CYLINDER HEAD IGNITION COIL - R+R.

Proceed with refitting

Op. 1072B50 SLEEVES CONNECTING AIR CAPACITY BOX TO INLET MANIFOLD IS - R+R.

Proceed with refitting

Op. 1016A30 LEFT CAM COVER - R + R AND REPLACE GASKET.

Proceed with refitting

Op. 5510C16 LEFT HAND CYLINDER HEAD IGNITION COIL - R+R.

Proceed with refitting

Op. 1016A42 LEFT HAND CYLINDER HEAD IGNITION COIL COVER - R+R.

Proceed with refitting

Op. 1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R + R.

Proceed with refitting

Op. 1092A10 CRANKSHAFT SERVICES PULLEY - R.R..

Proceed with refitting

Op. 1092G10 SINGLE ENGINE BELT R R.

Proceed with refitting

Op. 7055B64 LH OR RH REFLECTOR(ONE) ON REAR BUMPERS - R R.

Proceed with refitting

Op. 4450B04 RIGHT FRONT WHEEL R R.

Remove the car from the ramps.