Intermediate drive shaft mount - r r

Operation 2710A35 · Drive shafts and joints

1.9 JTD 8V

Removing

Ensure that the ignition key is in the stop position, then disconnect the battery negative terminal.

Proceed with removal

Op. 7055B54 PROTECTION/GUARD UNDER ENGINE - R.R.

Proceed with removal

1. Remove the bevel and undo the nut fixing the right driveshaft to the wheel hub.

Op. 4450B04 RIGHT FRONT WHEEL - R.R.

1. Undo the nut (1a) and disconnect the track rods (1b) from the steering knuckles usiing the tool (1c).

1. Undo the bolts fixing the intermediate driveshaft to the support.

1. Release the right driveshaft (1a), complete with intermediate driveshaft (1b) and remove it.

2. Remove the dust excluder.

Proceed with removal

Op. 1092G10 SINGLE ENGINE BELT - R.R.

1. Disconnect the electrical connections from the alternator.

1. Undo the bolt (1a) and remove the electrical wiring mounting bracket (1b) from the intermediate shaft support.

1. Undo the upper alternator fixing bolt.

1. Undo bolts (1a) and remove the upper alternator mounting bracket (1b).

1. Loosen the lower alternator fixing bolt, then partly release the bolt.

1. Undo the bolts (1a) and remove the intermediate driveshaft mounting (1b).

Refitting

1. Place the intermediate driveshaft support (1a) back in its housnig and fix it tightening the bolts (1b) to the recommended torque.

Completely fit the lower alternator fixing bolt and screw in the nut but do not fully tighten it.

Place the upper alternator mounting bracket back in its housing and fix it using the bolts.

Tighten the bolts fixing the alternator to the recommended torque.

Connect the electrical connections to the alternator.

Place the electrical wiring mounting bracket in its housing on the intermediate shaft support and secure it using the bolt.

Proceed with refitting

Op. 1092G10 SINGLE ENGINE BELT - R.R.

Place the right driveshaft, complete with intermediate driveshaft and dust excluder back in its housing.

1. Tighten the bolt fixing the intermediate driveshaft to the support to the recommended torque.

1. Connect the steering links (1a) to the front steering knuckles and tighten the nuts (1b) to the recommended torque.

1. Tighten the nuts (1a) securing the front wheel hub to the right driveshaft to the recommended torque, using the angular tightening tool (1b).

1. Bevel the collar of the nut in two places as shown in the figure.

Proceed with refitting

Op. 4450B04 RIGHT FRONT WHEEL - R.R.

Proceed with refitting

Connect the negative (-) battery terminal

Op. 7055B54 PROTECTION/GUARD UNDER ENGINE - R.R.

1.3 JTD 16V

Removing

Position the car on the ramp.

Make sure that the ignition key is in the OFF position and disconnect the battery negative terminal.

Carry out

Op. 4450B04 RIGHT FRONT WHEEL - R.R.

Carry out

Op. 7055B54 PROTECTION/GUARD UNDER ENGINE - R.R.

Carry out

Op. 2710A31 INTERMEDIATE DRIVESHAFT - R.R.

Carry out

Op. 2710A32 INTERMEDIATE DRIVESHAFT BEARING SUPPORT - R + R WITH INTERMEDIATE DRIVESHAFT REMOVED

Refitting

Carry out

Op. 2710A32 INTERMEDIATE DRIVESHAFT BEARING SUPPORT - R + R WITH INTERMEDIATE DRIVESHAFT REMOVED

Carry out

Op. 2710A31 INTERMEDIATE DRIVESHAFT - R.R.

Carry out

Op. 7055B54 PROTECTION/GUARD UNDER ENGINE - R.R.

Carry out

Op. 4450B04 RIGHT FRONT WHEEL - R.R.

Connect the battery negative terminal.

Remove the car from the ramps.