Vehicle drift
- Make
- Fiat
- Model
- Doblò Factory Service Manual
- Year
- 2000–2010
- Section
- STEERING – vehicle behaviour › Vehicle drift
Fault diagnosisVehicle drift
VEHICLE DRIFT
| Results of the tests | ||||
| 0 | PRELIMINARY CHECKS | All OK | Problems met | Operation |
|---|---|---|---|---|
Verify:
| Continue to Step 1 | Abnormal front tyre wear | Replace the tyres Op. 4450B21and carry out balancing | |
| Abnormal rear tyre wear | Replace the tyres Op. 4450B21 | |||
| Geometry not correct | Restore the correct geometry Op. 4450A10 | |||
| Wheels braked: front hub bearing fault | Replace the components involved Op. 4450C32 | |||
| Wheels braked: front hub fault | Replace the components involved Op. 4450C10 | |||
| Wheels braked: front caliper fault | Replace the components involved Op. 3310A30 | |||
| Wheels braked: rear bearing or hub fault | Replace the components involved Op. 4450D10 | |||
| 1 | CHECK ON DRIFT | All OK | Problems met | Operation |
| Test the vehicle on a straight line, on a good road surface and with no wind and check that there is no drift | The car drifts | Swap over the front wheels Continue to Step 2 | ||
| 2 | CHECK ON DRIFT | All OK | Problems met | Operation |
| Test the vehicle on a straight line, on a good road surface and with no wind and check that there is no drift | The drift has changed direction | Replace the tyres Op. 4450B21 Continue to Step 3 | ||
| The car continues to drift in the same direction | Swap over the front/rear wheels on the same side Continue to Step 3 | |||
| 3 | CHECK WHEEL GEOMETRY | All OK | Problems met | Operation |
| Check the front and rear wheel geometry | Continue to Step 4 | Geometry irregular | Restore the correct geometry Op. 4450A10 | |
| Wheels braked: front hub bearing fault | Replace the components involved Op. 4450C32 | |||
| Wheels braked: front hub fault | Replace the components involved Op. 4450C10 | |||
| wheels braked: rear bearing or hub fault | Replace the components involved Op. 4450D10 | |||
| 4 | CHECK ON STEERING WHEEL LOAD | All OK | Problems met | Operation |
| Check that during steering, there are no changes in load on the still steering wheel with wheels both on the ground and raised | Continue to Step 5 | A change in load on the steering wheel is observed | Rotate the steering column by 90° around its axis and re-align the steering wheel spokes Op. 4410A14 | |
| 5 | CHECK ON DRIFT | All OK | Problems met | Operation |
| Test the vehicle on a straight line, on a good road surface and with no wind and check that there is no drift | Continue to Step 6 | The vehicle still drifts | Replace the differential unit Op. 2110D10 | |
| 6 | CHECK ON STEERING WHEEL RETURN | All OK | Problems met | Operation |
| Test the vehicle on a straight line, on a good road surface and with no wind and check that there is no drift when the steering wheel returns after a steering action | Continue to Step 7 | The vehicle drifts on return of the steering wheel: different caster on right and left | Restore the correct caster Op. 4450A10 | |
| 7 | CHECK ON CORRECT OPERATION | All OK | Problems met | Operation |
| Check that the fault is no longer present | Fault persists | Search for the fault starting from another symptom' | ||
Parts & tools for this job For 2000 Fiat Doblò
- TOOLTie rod end toolSearch: tie rod end puller
- TOOLBall joint separatorSearch: ball joint separator
- FLUIDPower steering fluidSearch: Fiat power steering fluid
Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.