Workshop Manuals Factory service & repair Fiat
01 General information02 Specifications03 Manufacturing data and tolerances04 Tightening torques05 Fluids and lubricants06 Maintenance07 Diagnostic checks08 Engine09 Clutch10 Gearbox and differential11 Axles and driveshafts12 Brakes13 Steering14 Suspension and wheels15 Heating, air conditioning and auxiliary units16 Electrical equipment17 Body fittings18 Body panels and frame19 Wiring diagrams and electrical functions20 Wiring harnesses21 Connectors and pin-outs22 Fault diagnosis23 Special tools
Fiat Multipla Factory Service Manual (1998-2010)08 · Engine
08 · Engine

Water pump - r + r

Make
Fiat
Model
Multipla Factory Service Manual
Year
1998–2010
Section
Engine cooling › Water pump - r + r
EngineWater pump - r + r

Water pump - r + r

Operation 1088C10 · Water pump and thermostat

1.6 16v

Removing

Place the car on a ramp.

Open the bonnet lid.

With the ignition key in the OFF position, disconnect the battery negative terminal.

- 4450B10 Front WHEEL (one) - R.R.

1. Place a container under the vehicle to collect the engine coolant, then disconnect the lower hose from the radiator.

Water pump - r + r

- 1072C44 exhaust manifold heat shield on bulkhead - r+r

- 1092B50 alternator/air conditioner compressor drive belt - adjust tension

- 1092C10 power steering and/or self-levelling suspension pump drive belt - r + r

1. Undo the power steering pump retaining nuts.

2. Move the power steering pump to one side without disconnecting both oil hoses.

Water pump - r + r

1. Undo bolt (1a) securing the bracket to the crankcase and bolt (1b) securing the water pump to the crankcase.

2. Remove the bracket.

Raise the ramp.

3. Loosen the lower alternator bolt.

4. Tip the alternator down to gain access to the water pump fastenings.

Water pump - r + r

1. Unscrew bolts (1a) securing filler pipe (1b).

2. Unscrew the water pump bolts.

3. Remove the water pump and mount.

Water pump - r + r

Refitting

Fit the water pump and mount.

Tighten the bolts securing the water pump to the crankcase to torque.

FasteningComponentØ

Value

(daNm)

BoltCOOLANT PUMPM62.5

Tighten the bolts securing the water pump to the rigid filler pipe to torque.

FasteningComponentØ

Value

(daNm)

BoltCOOLANT PUMPM62.5

Fit the bracket and tighten the bolts.

FasteningComponentØ

Value

(daNm)

BoltALTERNATOR SUPPORTM105

Tip the alternator up and tighten the bolt securing it to the mount.

Tighten the alternator bolts to torque.

FasteningComponentØ

Value

(daNm)

BoltALTERNATOR ASSEMBLYM12 x 1.258.5

Fit the power steering pum in its seat.

Tighten the power steering bolt and nut.

- 1092C10 power steering and/or self-levelling suspension pump drive belt - r + r

- 1092B50 alternator/air conditioner compressor drive belt - adjust tension

- 1072C44 exhaust manifold heat shield on bulkhead - r+r

Connect the lower radiator hose.

- 1088A10 Engine COOLANT - Check density' and top up level, if necessary

- 4450B10 Front WHEEL (one) - R.R.

With the ignition key in the off position, connect the battery negative terminal.

Close the bonnet lid.

Remove the vehicle from the ramp.

1.9 JTD 8V

Removing

- 1088C12 water pump - r+r for versions with air conditioner

Parts & tools for this job For 1998 Fiat Multipla

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.