08 · Engine

Front crank shaft cover oil seal - replace

Make: Fiat
Model: Ulysse Factory Service Manual
Year: 2002–2010
Section: Crankcase sump and covers › Front crank shaft cover oil seal - replace

‹ Prev Engind front cover - r r Next › Flywheel side oil seal - replace

EngineFront crank shaft cover oil seal - replace

FRONT CRANK SHAFT COVER OIL SEAL - REPLACE

Operation 1020D18 · OIL SEALS ON CRANKSHAFT

3.0 24V V6

Removing

- Position the vehicle on the lift.

- Disconnect the negative battery terminal.

	Description	Connector
	Battery	A001B

Op. 4450B04 RIGHT FRONT WHEEL R R

Op. 7055B54 UNDER-ENGINE GUARD - R R

Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.

Op. 5010B18 CLIMATE CONTROL UNIT AIR INTAKE - R.R.

Op. 5050B34 WINDSCREEN WIPER ARM/S COMPLETE WITH BLADE - R+R

Op. 7210E22 WINDSCREEN BASE TRIM

See in Op. 1088B10

Op. 4130B10 POWER STEERING FLUID RESEVOIR R R

Op. 4130B12 POWER STEERING FLUID RESERVOIR MOUNTING/BRACKETS - POSITION

Op. 1016A42 LEFT HAND CYLINDER HEAD IGNITION COIL COVER - R+R

See in Op. 1008C10

Op. 4410D16 BRACKET (ONE) RETAINING CHASSIS TO BODY - R R

See in Op. 1092G10

See in Op. 1092A10

See in Op. 1092G15

See in Op. 1092G21

See in Op. 1032D12

See in Op. 1008A46

See in Op. 1008B10

Op. 1092C14 POWER STEERING PUMP/SELF LEVELLING SUSPENSION PUMP PULLEY - R + R WITH BELT REMOVED

Op. 1032B14 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT VERSIONS WITH AIR CONDITIONER

See in Op. 1032B44

- Remove the oil seal from the front cover using a suitable tool without damaging the housing

Because the oil seal must always be replaced, it may be destroyed when it is removed.

Refitting

1. Refit a new oil seal (1b) on the crankshaft front cover using the tool (1a).

	Description	Code	Function
1a	Fitting tool	1.870.900.100	Engine oil front cover oil seal

FRONT CRANK SHAFT COVER OIL SEAL - REPLACE

See in Op. 1032B44

Op. 1032B14 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT VERSIONS WITH AIR CONDITIONER

Op. 1092C14 POWER STEERING PUMP/SELF LEVELLING SUSPENSION PUMP PULLEY - R + R WITH BELT REMOVED

See in Op. 1008B10

See in Op. 1008A46

See in Op. 1032D12

See in Op. 1092G21

See in Op. 1092G15

See in Op. 1092A10

See in Op. 1092G10

Op. 4410D16 BRACKET (ONE) RETAINING CHASSIS TO BODY - R R

See in Op. 1008C10

Op. 1016A42 LEFT HAND CYLINDER HEAD IGNITION COIL COVER - R+R

Op. 4130B12 POWER STEERING FLUID RESERVOIR MOUNTING/BRACKETS - POSITION

Op. 4130B10 POWER STEERING FLUID RESEVOIR R R

See in Op. 1088B10

Op. 7210E22 WINDSCREEN BASE TRIM

Op. 5050B34 WINDSCREEN WIPER ARM/S COMPLETE WITH BLADE - R+R

Op. 5010B18 CLIMATE CONTROL UNIT AIR INTAKE - R.R.

Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.

Op. 7055B54 UNDER-ENGINE GUARD - R R

Op. 4450B04 RIGHT FRONT WHEEL R R

- Connect the negative battery terminal.

	Description	Connector
	Battery	A001B

Op. 0010T70 POWER ASSISTED STEERING FLUID - REPLACE

Op. 0010T21 COOLANT CHECK DENSITY AND TOP UP IF NECESSARY

- Remove the vehicle from the lift.

2.0 16v

Removing

See in Op. 1088B10

Op. 7055B54 UNDER-ENGINE GUARD - R R

Op. 4450B04 RIGHT FRONT WHEEL R R

Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.

Op. 4410D16 BRACKET (ONE) RETAINING CHASSIS TO BODY - R R

- < R1 > [Right side, front]

See in Op. 1092G10

See in Op. 1092A10

See in Op. 1032D12

See in Op. 1032B10

See in Op. 1032B44

- Remove the oil sealing ring from its seat on the front cover.

Because the oil seal must always be replaced, it may be destroyed when it is removed.

Refitting

1. Using the tool, fit the seal on the crankshaft front cover.

	Description	Code	Function
	Fitting tool	1.870.883.000	Fitting crankshaft front oil seal

See in Op. 1032B44

See in Op. 1032B10

See in Op. 1032D12

See in Op. 1092A10

See in Op. 1092G10

Op. 4410D16 BRACKET (ONE) RETAINING CHASSIS TO BODY - R R

- < R1 > [Right side, front]

Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.

Op. 4450B04 RIGHT FRONT WHEEL R R

Op. 7055B54 UNDER-ENGINE GUARD - R R

See in Op. 1088B10

Op. 0010T21 COOLANT CHECK DENSITY AND TOP UP IF NECESSARY

2.0 16V JTD

Removing

Op. 4450B04 RIGHT FRONT WHEEL R R

Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.

Op. 7055B54 UNDER-ENGINE GUARD - R R

Op. 5530B56 BATTERY DRIP TRAY COVER - R.R.

Op. 5010B18 CLIMATE CONTROL UNIT AIR INTAKE - R.R.

Op. 5050B34 WINDSCREEN WIPER ARM/S COMPLETE WITH BLADE - R+R

Op. 7055A18 L/H OR R/H SIDE RUBBING STRIP DECORATIVE SEAL - R+R

Op. 5050B38 WINDSCREEN WIPER ASSEMBLY - R+R OR REPAIR

See in Op. 1008C10

See in Op. 1092G10

See in Op. 1024B54

See in Op. 1092A10

See in Op. 1032D12

See in Op. 1008A46

See in Op. 1032B10

See in Op. 1032B44

- Remove the oil seal from the housing in the front cover.

Because the oil seal must always be replaced, it may be destroyed when it is removed.

Refitting

1. Fit the oil seal (1a) using the tool (1b) in the housing in the crankshaft front cover.

	Description	Code	Function
1	Fitting tool	1.860.855.000	Front cover gasket fitting

See in Op. 1032B44

See in Op. 1032B10

See in Op. 1008A46

See in Op. 1032D12

See in Op. 1092A10

See in Op. 1024B54

See in Op. 1092G10

See in Op. 1008C10

Op. 5050B38 WINDSCREEN WIPER ASSEMBLY - R+R OR REPAIR

Op. 7055A18 L/H OR R/H SIDE RUBBING STRIP DECORATIVE SEAL - R+R

Op. 5050B34 WINDSCREEN WIPER ARM/S COMPLETE WITH BLADE - R+R

Op. 5010B18 CLIMATE CONTROL UNIT AIR INTAKE - R.R.

Op. 5530B56 BATTERY DRIP TRAY COVER - R.R.

Op. 7055B54 UNDER-ENGINE GUARD - R R

Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.

Op. 4450B04 RIGHT FRONT WHEEL R R

2.2 16V JTD

Removing

Op. 4450B04 RIGHT FRONT WHEEL R R

Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.

Op. 7055B54 UNDER-ENGINE GUARD - R R

Op. 5530B56 BATTERY DRIP TRAY COVER - R.R.

Op. 5010B18 CLIMATE CONTROL UNIT AIR INTAKE - R.R.

Op. 5050B34 WINDSCREEN WIPER ARM/S COMPLETE WITH BLADE - R+R

Op. 7055A18 L/H OR R/H SIDE RUBBING STRIP DECORATIVE SEAL - R+R

Op. 5050B38 WINDSCREEN WIPER ASSEMBLY - R+R OR REPAIR

See in Op. 1008C10

See in Op. 1092G10

See in Op. 1024B54

See in Op. 1092A10

See in Op. 1032D12

See in Op. 1008A46

See in Op. 1032B10

See in Op. 1032B44

- Remove the oil seal from the housing in the front cover.

Because the oil seal must always be replaced, it may be destroyed when it is removed.

Refitting

1. Fit the oil seal (1a) using the tool (1b) in the housing in the crankshaft front cover.

	Description	Code	Function
1	Fitting tool	1.860.855.000	Front cover gasket fitting

See in Op. 1032B44

See in Op. 1032B10

See in Op. 1008A46

See in Op. 1032D12

See in Op. 1092A10

See in Op. 1024B54

See in Op. 1092G10

See in Op. 1008C10

Op. 5050B38 WINDSCREEN WIPER ASSEMBLY - R+R OR REPAIR

Op. 7055A18 L/H OR R/H SIDE RUBBING STRIP DECORATIVE SEAL - R+R

Op. 5050B34 WINDSCREEN WIPER ARM/S COMPLETE WITH BLADE - R+R

Op. 5010B18 CLIMATE CONTROL UNIT AIR INTAKE - R.R.

Op. 5530B56 BATTERY DRIP TRAY COVER - R.R.

Op. 7055B54 UNDER-ENGINE GUARD - R R

Op. 7055B91 RIGHT FRONT WHEEL ARCH LINER - R.R.

Op. 4450B04 RIGHT FRONT WHEEL R R

‹ Prev Engind front cover - r r Next › Flywheel side oil seal - replace

Parts & tools for this job For 2002 Fiat Ulysse

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.