Engine Data Description | 1.3L | 1.6L | Engine code | JNTA | CLTA/CDTA | Bore | 73.95 | 82.07 mm | Stroke | 75.48 | 75.48 mm | Cubic capacity | 1297 | 1597 cc | Compression ratio | 10.2:1 | 9.5 : 1 | Power output at 5500 rpm | 51 kW (69 PS) | 68 kW (92.5 PS) | Max. torque at 2500 rpm | 102 Nm | 134 Nm | Torque at 1500 rpm | 90 Nm | 118 Nm | Max. engine speed (intermittent) | 6175 rpm | 6175 rpm | Max. engine speed (continuous) | 5950 rpm | 5950 rpm | Idle speed | 880 rpm | 880 rpm | Number of main bearings | 5 | 5 | Camshaft drive | Chain | Chain | Lubricants, Fluids, Sealers and Adhesives Item | Specification | Sealant | WSK-M2G349-A4 | Sealant | WSE-M4G323-A4 | High-temperature grease | WSD-M1C230-A | Engine Oil Recommended engine oil | Viscosity/Temperature | Specification | Ford Formula E Economy Motor Oil | SAE 5W-30/-20°C to over +40°C | WSS-M2C913-A or WSS-M2C912-A1 | Capacities | Litres | Engine oil, initial fill including filter | 4.45 | Engine oil, including filter change | 4.35 | Engine oil, excluding filter change | 3.90 | Oil System Description | bar | Pressure relief valve opening pressure | 5.0 - 6.0 | Valves - 1.3L Description | mm | Valve spring free length | 43.20 | Valve spring inner diameter (intake and exhaust) | 18.80 - 19.20 | Valve spring material diameter | 3.70 | Number of valve spring coils | 6.70 | Valve (intake) overall length | 109.37 - 109.83 | Valve (exhaust) overall length | 109.68 - 110.05 | Valve head (intake) diameter | 34.97 - 35.23 | Valve head (exhaust) diameter | 29.57 - 29.83 | Valve stem diameter (intake and exhaust) | 5.957 - 5.975 | Valve stem to valve guide clearance (intake and exhaust) | 0.025 - 0.073 | Valve lift (intake and exhaust) | 9.74 | Valves - 1.6L Description | mm | Valve spring free length | 43.20 | Valve spring inner diameter (intake and exhaust) | 18.80 - 19.20 | Valve spring material diameter | 3.70 | Number of valve spring coils | 6.70 | Valve (intake) overall length | 109.37 - 109.83 | Valve (exhaust) overall length | 109.68 - 110.05 | Valve head (intake) diameter | 39.87 - 40.13 | Valve head (exhaust) diameter | 33.87 - 34.13 | Valve stem diameter (intake and exhaust) | 5.967 - 5.985 | Valve stem to valve guide clearance (intake and exhaust) | 0.015 - 0.053 | Valve lift (intake and exhaust) | 9.74 | Camshaft Description | mm | Valve lift cam (intake and exhaust) | 9.74 | Camshaft bearing journal diameter | 23.96 - 23.98 | Camshaft bearing journal bore diameter | 24.00 - 24.03 | Camshaft end float | 0.075 - 0.185 | Valve Timing - 1.3L Description | Degrees | Valve timing, intake opens (1 mm lift) after TDC | 14 | Valve timing, intake closes (1 mm lift) after BDC | 26 | Valve timing, exhaust opens (1 mm lift) before BDC | 26 | Valve timing, exhaust closes (1 mm lift) before TDC | 14 | Valve Timing - 1.6L Description | Degrees | Valve timing, intake opens (1 mm lift) after TDC | 12 | Valve timing, intake closes (1 mm lift) after BDC | 24 | Valve timing, exhaust opens (1 mm lift) before BDC | 24 | Valve timing, exhaust closes (1 mm lift) before TDC | 12 | Crankshaft Description | mm | Crankshaft main bearing journal diameter (standard) | 56.980 - 57.00 | Crankshaft main bearing journal diameter (undersize) | 56.726 - 56.746 | Crankshaft main bearing journal shell width | 18.290 - 18.690 | Crankshaft connecting rod journal diameter (standard) | 40.990 - 41.010 | Crankshaft connecting rod journal diameter (undersize) | 40.740 - 40.760 | Crankshaft connecting rod journal diameter (service 0.508 mm) | 40.490 - 40.510 | Crankshaft connecting rod journal diameter (service 0.762 mm) | 40.240 - 40.260 | Crankshaft end play | 0.075 - 0.285 | Crankshaft thrust washer thickness (standard) | 2.800 - 2.850 | Crankshaft thrust washer thickness (oversize) | 2.99 - 3.040 | CAUTION:The crankshaft must not be machined. Pistons - 1.3L Description | | Piston diameter, class 1 | 73.932 - 73.917 mm | Piston diameter (oversize 0.15 mm) | 74.082 - 74.067 mm | Piston diameter (oversize 0.50 mm) | 74.432 - 74.417 mm | Piston to cylinder bore clearance | 0.020 - 0.050 mm | Piston ring end gap (installed) (top) | 0.20 - 0.40 mm | Piston ring end gap (installed) (second) | 0.25 - 0.50 mm | Piston ring end gap (installed) oil | 0.25 - 0.75 mm | Piston ring-to-groove clearance (top) | 0.020 - 0.055 mm | Piston ring-to-groove clearance (second) | 0.030 - 0.060 mm | Piston ring end gap position (top) | 120 degrees offset from second ring end gap | Piston ring end gap position (second) | Aligned with piston pin | Piston ring end gap position, oil | 120 degrees offset from second ring end gap* | Piston pin length | 51.700 - 52.000 mm | Piston pin diameter | 18.030 - 18.034 mm | Piston pin to bore diameter interference | 0.012 - 0.036 mm | Piston pin slide clearance (21°C) | 0.012 - 0.020 mm | *) Rails and expander 120 degrees. Pistons - 1.6L Description | | Piston diameter, class 1 | 82.035 - 82.050 mm | Piston diameter (oversize 0.15 mm) | 82.185 - 82.200 mm | Piston diameter (oversize 0.50 mm) | 82.535 - 82550 mm | Piston to cylinder bore clearance | 0.020 - 0.050 mm | Piston ring end gap (installed) (top) | 0.20 - 0.40 mm | Piston ring end gap (installed) (second) | 0.25 - 0.50 mm | Piston ring end gap (installed) oil | 0.25 - 1.0 mm | Piston ring-to-groove clearance (top) | 0.022 - 0.057 mm | Piston ring-to-groove clearance (second) | 0.030 - 0.070 mm | Piston ring end gap position (top) | 120 degrees offset from second ring end gap | Piston ring end gap position (second) | Aligned with piston pin | Piston ring end gap position, oil | 120 degrees offset from second ring end gap* | Piston pin length | 53.300 - 53.600 mm | Piston pin diameter | 18.030 - 18.034 mm | Piston pin to connecting rod small end diameter clearance | 0.012 - 0.036 mm | Piston pin to pin bore clearance (21°C) | 0.012 - 0.020 mm | *) Rails and expander 120 degrees. Connecting Rods Description | mm | Connecting rod large end bore diameter | 43.99 - 44.01 | Connecting rod small end bore diameter | 17.998 - 18.018 | Connecting rod bearing shell, vertical inner diameter, standard | 41.016 - 41.050 | Connecting rod bearing shell, vertical inner diameter, undersize 0.254 mm | 40.966 - 41.000 | Connecting rod bearing shell, vertical inner diameter, undersize 0.508 mm | 40.516 - 40.550 | Connecting rod bearing shell, vertical inner diameter, undersize 0.762 mm | 40.226 - 40.300 | Connecting rod bearing shell, vertical inner diameter, undersize 1.016 mm | 40.016 - 40.050 | Connecting rod bearing clearance (radial) | 0.006 - 0.060 | Connecting rod bearing clearance (axial) | 0.100 - 0.250 | Cylinder Block - 1.3L Description | mm | Cylinder bore diameter, standard | 73.967 - 73.952 | Cylinder bore diameter (oversize 0.15 mm) | 74.117 - 74.102 | Cylinder bore diameter (oversize 0.50 mm) | 74.467 - 74.452 | Center main bearing width (without thrust half-washers) | 22.040 - 22.100 | Main bearing shells, vertical inner diameter (installed), standard | 57.009 - 57.056 | Main bearing shells, vertical inner diameter (installed), undersize 0.254 mm | 56.755 - 56.802 | Main bearing shells, vertical inner diameter (installed), undersize 0.508 mm | 56.501 - 56.548 | Main bearing shells, vertical inner diameter (installed), undersize 0.762 mm | 56.247 - 56.294 | Main bearing parent bore diameter, standard | 60.623 - 60.636 | Main bearing parent bore diameter, oversize | 61.003 - 61.016 | Cylinder Block - 1.6L Description | mm | Cylinder bore diameter, standard | 82.070 - 82.085 | Cylinder bore diameter (oversize 0.15 mm) | 82.220 - 82.235 | Cylinder bore diameter (oversize 0.50 mm) | 82.570 - 82.585 | Center main bearing width (without thrust half-washers) | 22.040 - 22.100 | Main bearing shells, vertical inner diameter (installed), standard | 57.009 - 57.056 | Main bearing shells, vertical inner diameter (installed), undersize 0.254 mm | 56.755 - 56.802 | Main bearing shells, vertical inner diameter (installed), undersize 0.508 mm | 56.501 - 56.548 | Main bearing shells, vertical inner diameter (installed), undersize 0.762 mm | 56.247 - 56.294 | Main bearing parent bore diameter, standard | 60.623 - 60.636 | Main bearing parent bore diameter, oversize | 61.003 - 61.016 | Torque Specifications Description | Nm | lb-ft | lb-in | Oil gallery plug, 1/2" | 22 | 16 | - | Crankshaft main bearing retaining bolts | 95 | 70 | - | Crankshaft rear oil seal retainer retaining bolts | 10 | - | 89 | Crankshaft position (CKP) sensor retaining bolt | 10 | - | 89 | Crankshaft pulley retaining bolt | 125 | 92 | - | Knock sensor (KS) retaining bolt | 20 | 15 | | Connecting rod retaining bolts | a) | - | - | Hydraulic timing chain tensioner | 40 | 30 | - | Timing chain tensioner arm retaining bolt | 26 | 19 | - | Timing chain guide retaining bolt | 26 | 19 | - | Oil pump retaining bolts | 20 | 15 | - | Oil pump pick-up pipe retaining bolt | 10 | - | 89 | Oil pan baffle retaining nuts | 19 | 14 | - | Oil pan retaining bolts | a) | - | - | Oil filter adaptor | 20 | 15 | - | Oil pressure switch | 20 | 15 | - | Oil drain plug | 25 | 18 | - | Oil level indicator tube retaining bolts | 20 | 15 | - | Accessory drive belt idler pulley retaining bolt | 48 | 35 | - | Water pump retaining bolts | 10 | - | 89 | Water pump pulley retaining bolts | 12 | 9 | - | Coolant expansion tank retaining bolt | 10 | - | 71 | Power steering pump retaining bolts | 25 | 18 | - | Power steering supply line retaining bracket retaining bolt | 20 | 20 | - | Flywheel retaining bolts | 67 | 49 | - | Air conditioning (A/C) compressor retaining bolts | 25 | 18 | - | Starter motor retaining bolts | 35 | 26 | - | Engine lifting eye | 20 | 15 | - | Cylinder head bolts | a) | - | - | Camshaft sprocket retaining bolt | 75 | 55 | - | Camshaft bearing cap retaining bolts | 9 | - | 80 | Camshaft position (CMP) sensor retaining bolt | 5 | - | 44 | Valve cover retaining bolts | 9 | - | 80 | Ignition coil retaining bolts | 6 | - | 53 | Coolant flow control housing retaining bolts | 10 | - | 89 | Spark plugs | 15 | 11 | - | Intake manifold retaining nuts | 18 | 13 | - | Intake manifold retaining bolts | 18 | 13 | - | Exhaust manifold retaining nuts | a) | - | - | Exhaust manifold heat shield retaining bolts | 10 | - | 89 | Engine front mount to engine front mount retaining bracket | 48 | 35 | - | Engine front mount retaining bracket to cylinder head bolts | 25 | 18 | - | Flexible exhaust pipe to exhaust manifold retaining nuts | 47 | 35 | - | Engine rear mount center bolt | 90 | 66 | - | Transaxle upper retaining bolt | 44 | 32 | - | Transaxle lower retaining bolts | 44 | 32 | - | Transaxle left-hand retaining bolt | 44 | 32 | - | Transaxle right-hand retaining bolts | 44 | 32 | - | Engine support insulator to crossmember retaining bolts | 48 | 35 | - | Engine support insulator to transaxle retaining bolts | 48 | 35 | - | Lower arm retaining bolt | 47 | 35 | - | Strut and spring assembly top mount retaining nuts | 25 | 18 | - | a) Refer to procedure in this section. | |