Workshop Manuals Factory service & repair Land Rover
01 Discovery Workshop Manual - 2nd Edition02 01 - INTRODUCTION03 04 - GENERAL SPECIFICATION DATA04 05 - ENGINE TUNING DATA05 07 - GENERAL FITTING REMINDERS06 09 - LUBRICANTS, FLUIDS AND CAPACITIES07 10 - MAINTENANCE08 12 - ENGINE - Tdi09 10 11 12 12 - ENGINE - V8i13 12 - ENGINE - 4.0 V814 12 - ENGINE - Mpi15 16 17 18 17 - EMISSION CONTROL19 19 - FUEL SYSTEM - Tdi20 19 - FUEL SYSTEM - MFI21 19 - FUEL SYSTEM - SFI22 19 - FUEL SYSTEM - Mpi23 19 - FUEL SYSTEM - Cruise Control24 26 - COOLING SYSTEM - Tdi25 26 - COOLING SYSTEM - V8i26 26 - COOLING SYSTEM - Mpi27 28 30 - MANIFOLD AND EXHAUST SYSTEM29 33 - CLUTCH30 37 - MANUAL GEARBOX - R38031 41 - TRANSFER GEARBOX32 44 - AUTOMATIC GEARBOX - ZF33 34 35 47 - PROPELLER SHAFTS36 51 - REAR AXLE AND FINAL DRIVE37 38 54 - FRONT AXLE AND FINAL DRIVE39 40 41 57 - STEERING42 43 44 60 - FRONT SUSPENSION45 64 - REAR SUSPENSION46 70 - BRAKES47 74 - WHEELS AND TYRES48 75 - SUPPLEMENTARY RESTRAINT SYSTEM49 76 - CHASSIS AND BODY50 51 80 - HEATING AND VENTILATION52 82 - AIR CONDITIONING53 84 - WIPERS AND WASHERS54 86 - ELECTRICAL
Land Rover 300Tdi Discovery18 · 17 - EMISSION CONTROL
18 · Engine

17 - EMISSION CONTROL: DESCRIPTION AND OPERATION (page 3 of 3)

Make
Land Rover
Model
Discovery 300Tdi Discovery
17 - EMISSION CONTROLDESCRIPTION AND OPERATION · page 3 of 3
17 - EMISSION CONTROL: DESCRIPTION AND OPERATION (page 3 of 3) – Land Rover 300Tdi Discovery

17

EMISSION CONTROL

8

DESCRIPTION AND OPERATION

ADD: 09/95

System operation

The system is designed to prevent fuel vapour
escaping to atmosphere, and consists of four roll-over
valves fitted internally in the fuel tank, connected to
the liquid/vapour separator by a nylon line. The
separator is mounted to the side of the filler neck. An
EVAP canister is positioned in the engine
compartment mounted on the right front side valance.
The liquid/vapour separator and EVAP canister are
connected by a nylon line which runs the length of the
chassis.

Pressure/vacuum relief valves are incorporated into
the fuel filler cap and are designed to protect the fuel
tank from permanent deformation in the event of
system pressure or vacuum exceeding the system
operating parameters. There are no other relief or
one-way valves in the system.

A vent line flow restrictor known as an anti-trickle fill
valve is fitted to the filler pipe in the line between the
tank and EVAP canister. The function of this valve is
to prevent overfilling the tank by trickling fuel in,
thereby preserving the vapour space in the tank to
allow for fuel expansion during hot weather.

The valve achieves this by blocking the vent line
during the fuel filling process. The valve is operated
by the action of inserting the filler gun so that when
the fuel in the tank reaches the level of the filling
breather, flow cut off occurs due to fuel filling the filler
pipe.

During normal vehicle operation and when the engine
is switched off, the venting system between the fuel
tank and EVAP canister is open to allow the free
passage of vapour.

The EVAP canister, which is connected by a nylon
hose to the plenum chamber, absorbs and stores the
fuel vapour from the fuel tank when the engine is not
running. With the engine running, vapour is purged
from the EVAP canister by allowing outside air to be
drawn through the EVAP canister vent solenoid and
link pipe by the influence of manifold vacuum to the
EVAP canister purge connection on the canister.

Filter pads are fitted above and below the charcoal
and in the EVAP canister vent solenoid to prevent the
ingress of foreign matter into the purge line.

The EVAP canister purge valve, which is fitted in the
line from the EVAP canister to the plenum, is
controlled by the ECM which determines the most
emission acceptable time at which purging should
take place. This will normally be at engine speeds
above idle and when the vehicle is in motion.

The EVAP canister vent solenoid is mounted on the
side of the EVAP canister bracket and is connected to
the EVAP canister by a length of large bore hose. The
ECVS is controlled by the ECM and is normally open.
The function of the ECVS is to block the air intake
side of the EVAP canister. When the system receives
an ECM signal the valve closes; this allows the
system leak check to take place. The leak check only
occurs when pre-determined vehicle operating
conditions are met.

Parts & tools for this job For Land Rover Discovery

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.