HS 250h L4-2.4L (2AZ-FXE) Hybrid (2010)
(k) When disposing of the vehicle or an SRS part by itself, deploy it using SST before disposal. Deploy the SRS parts in a safe place away from
electrical noise.
HINT
*
Disposal of the steering pad See: Restraint Systems/Air Bag Systems/Air Bag/Service and Repair/Procedures/Steering Pad
*
Disposal of the driver side knee airbag assembly See: Restraint Systems/Air Bag Systems/Air Bag/Service and
Repair/Procedures/Knee Airbag Assembly (for Driver Side)
*
Disposal of the front passenger side knee airbag assembly See: Restraint Systems/Air Bag Systems/Air Bag/Service and
Repair/Procedures/Knee Airbag Assembly (for Front Passenger Side)
*
Disposal of the front passenger airbag assembly See: Restraint Systems/Air Bag Systems/Air Bag/Service and
Repair/Procedures/Front Passenger Airbag Assembly
*
Disposal of the curtain shield airbag assemblies See: Restraint Systems/Air Bag Systems/Air Bag/Service and
Repair/Procedures/Curtain Shield Airbag Assembly
*
Disposal of the front seat side airbag assemblies See: Restraint Systems/Air Bag Systems/Air Bag/Service and
Repair/Procedures/Front Seat Side Airbag Assembly
*
Disposal of the rear seat side airbag assemblies See: Restraint Systems/Air Bag Systems/Air Bag/Service and Repair/Procedures/Rear
Seat Side Airbag Assembly
*
Disposal of the front seat outer belt assemblies See: Restraint Systems/Seat Belt Systems/Seat Belt/Service and
Repair/Procedures/Front Seat Outer Belt Assembly
*
Disposal of the rear seat 3 point type belt assemblies See: Restraint Systems/Seat Belt Systems/Seat Belt/Service and
Repair/Procedures/Rear Seat Outer Belt Assembly
(l) Never inspect the resistance of the SRS parts.
CAUTION:
Never measure the resistance of the SRS parts because current from the tester may cause the SRS parts to deploy.
4. PRECAUTION FOR DISPOSAL OF SRS PARTS (NOT DEPLOYED)
(a) Before performing pre-disposal deployment of any SRS parts, review and closely follow all applicable environmental and hazardous material
regulations. Pre-disposal deployment may be considered hazardous material treatment.
(b) Never dispose of any SRS parts that are not deployed.
(c) Deploy the SRS parts outdoors in a safe and level place where it will not disturb nearby residents.
(d) As the SRS parts produce a loud sound when deployed, be sure to inform nearby residents before deployment.
(e) When deploying the SRS parts, always use SST and keep people at least 10 m (32.8 ft.) away.
(f) The SRS parts may be accidentally deployed by static electricity. To prevent this, be sure to touch a grounded metal surface with your bare
hands to discharge any static electricity before handling the SRS parts.
(g) Do not face the airbag deployment side down when deploying an airbag.
5. PRECAUTION FOR DISPOSAL OF SRS PARTS (DEPLOYED)
(a) As the SRS parts are very hot after being deployed, allow at least 30 minutes for them to cool down sufficiently before disposal.
(b) Do not apply water etc. to any deployed SRS parts.
(c) Use gloves and safety glasses when handling any deployed SRS parts.
(d) Seal the deployed SRS parts in a thick clear plastic bag when disposing them.
(e) Always wash your hands with water after disposing of deployed SRS parts.
6. PRECAUTION FOR STEERING PAD (DRIVER AIRBAG), DRIVER SIDE KNEE AIRBAG ASSEMBLY, FRONT PASSENGER SIDE
KNEE AIRBAG ASSEMBLY, FRONT PASSENGER AIRBAG ASSEMBLY, CURTAIN SHIELD AIRBAG ASSEMBLY, FRONT SEAT
SIDE AIRBAG ASSEMBLY AND REAR SEAT SIDE AIRBAG ASSEMBLY
(a) Keep the airbag deployment side facing upward even when the airbag is temporarily removed during an operation.
CAUTION:
Always place a removed or new airbag with the deployment surface facing upward. Placing the airbag with the deployment surface
facing downward could cause a serious accident if the airbag deploys.