LS 460 AWD V8-4.6L (1UR-FSE) (2009)
(1) Install the 2 member stoppers with the 4 bolts labeled B, and install the 4 bolts labeled A.
Torque: 19 Nm (194 kgf-cm, 14 ft-lbf)for bolt labeled A
Torque: 127 Nm (1295 kgf-cm, 94 ft-lbf)for bolt labeled B
(c) for Standard
(1) Install the 4 bolts labeled B.
Torque: 127 Nm (1295 kgf-cm, 94 ft-lbf)
5. CONNECT PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY LH (W/ Air Suspension) See: Control Arm/Service
and Repair/Rear Upper Arm/Installation
6. CONNECT PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY RH (W/ Air Suspension)
HINT: Use the same procedures described for the LH side.
7. CONNECT REAR SHOCK ABSORBER ASSEMBLY LH (W/O Air Suspension) See: Control Arm/Service and Repair/Rear Upper
Arm/Installation
8. CONNECT REAR SHOCK ABSORBER ASSEMBLY RH (W/O Air Suspension)
HINT: Use the same procedures described for the LH side.
9. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH See: Brakes and Traction Control/Disc Brake System/Service and Repair/Removal
and Replacement/Rear Brake/Installation
10. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY RH
HINT: Use the same procedures described for the LH side.
11. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY See: Transmission and Drivetrain/Drive/Propeller Shafts, Bearings
and Joints/Drive/Propeller Shaft/Service and Repair/Removal and Replacement/Propeller Shaft Assembly/Installation
12. INSPECT AND ADJUST NO. 2 AND NO. 3 JOINT ANGLE See: Transmission and Drivetrain/Drive/Propeller Shafts, Bearings and
Joints/Drive/Propeller Shaft/Service and Repair/Removal and Replacement/Propeller Shaft Assembly/Installation
13. INSTALL PROPELLER SHAFT HEAT INSULATOR See: Transmission and Drivetrain/Drive/Propeller Shafts, Bearings and
Joints/Drive/Propeller Shaft/Service and Repair/Removal and Replacement/Propeller Shaft Assembly/Installation
14. INSTALL FRONT FLOOR NO. 1 HEAT INSULATOR See: Transmission and Drivetrain/Drive/Propeller Shafts, Bearings and
Joints/Drive/Propeller Shaft/Service and Repair/Removal and Replacement/Propeller Shaft Assembly/Installation
15. INSTALL TAILPIPE RH See: Engine, Cooling and Exhaust/Exhaust System/Exhaust Pipe/Service and Repair/Installation
16. INSTALL TAILPIPE LH See: Engine, Cooling and Exhaust/Exhaust System/Exhaust Pipe/Service and Repair/Installation
17. INSTALL FRONT EXHAUST PIPE ASSEMBLY See: Engine, Cooling and Exhaust/Exhaust System/Exhaust Pipe/Service and
Repair/Installation
18. INSTALL FRONT FLOOR BRACE CENTER See: Engine, Cooling and Exhaust/Exhaust System/Exhaust Pipe/Service and Repair/Installation
19. INSTALL HEATED OXYGEN SENSOR (for Sensor 2) See: Engine, Cooling and Exhaust/Exhaust System/Exhaust Pipe/Service and
Repair/Installation
20. INSPECT FOR GAS LEAK
21. INSTALL PARKING BRAKE CABLE
(a) Install the cable with the 2 nuts to the vehicle side.
Torque: 8.0 Nm (82 kgf-cm, 71 in-lbf)
22. CONNECT NO. 1 ACTUATOR HARNESS CLAMP
(a) Connect the 2 clamps and connector.
23. INSTALL REAR SPEED SENSOR LH See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Wheel Speed
Sensor/Service and Repair/Rear Speed Sensor/Installation
24. INSTALL REAR SPEED SENSOR RH
HINT: Use the same procedures described for the LH side.