Leon Mk1
Display groups assembly overview |
Display group 000 - Decimal values- | ||||||||||||||
| ||||||||||||||
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | ← Display zones | ||||
Adaptive value for the active carbon filter solenoid valve 1 | ||||||||||||||
Battery voltage | ||||||||||||||
Adaptive value for the idle stabilization | ||||||||||||||
Adaptive value for basic air requirement | ||||||||||||||
Adaptive value for the mix correction | ||||||||||||||
Adaptive value for injector | ||||||||||||||
Idle switch | ||||||||||||||
Throttle potentiometer -tracks 1 and 2 | ||||||||||||||
Throttle potentiometer -track 1 | ||||||||||||||
Coolant temperature |
Display group 000 - Decimal values- | ||||||||||||||
| ||||||||||||||
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | ← Display zones | ||||
Adaptive value for the active carbon filter solenoid valve 1 | ||||||||||||||
Battery voltage | ||||||||||||||
Adaptive value for the idle stabilization | ||||||||||||||
Adaptive value for basic air requirement | ||||||||||||||
Adaptive value for the mix correction | ||||||||||||||
Lambda regulation | ||||||||||||||
Inlet air temperature | ||||||||||||||
Engine speed | ||||||||||||||
Throttle potentiometer -track 1 | ||||||||||||||
Coolant temperature |
Indication fields | ||||
1 | 2 | 3 | 4 | |
Indication field 01 - idle test - | ||||
Display | 0…xxxx/min | -xx,x…xxx,x °C | 0,xx…1,xx | xxxxxxxx |
Indication | Engine speed | Coolant temperature | Lambda correction factor | Charge status → Note |
Indication field 02 - injection timing, inlet air temperature - | ||||
Display | 0…xxxx/min | 0,0…xxx,x ms | 0,0…xx,x V | -xx,x…xxx,x °C |
Display | Engine speed | Injection timing | Battery voltage | Inlet air temperature |
Indication field 03 -Engine charge status - | ||||
Display | 0…xxxx/min | 0…xxx % | 0…xxx ∠° | -xx.x°b.TDCxx.x° a.TDC |
Indication | Engine speed | Engine charge signal | Throttle angle (calculated value, depends on the throttle potentiometer) | Ignition timing (calculated value, depending on the adjustment of the ignition instant → Note) |
1) | Meaning of the numbers in the 8 digit number block → Anchor |
2) | This value may not be used for the verification or the adjustment of ignition timing. |
Indication fields | ||||
1 | 2 | 3 | 4 | |
Indication field 04 - Operations stage - | ||||
Display | 0…xxxx/min | 0…xxx % | 0, >4, >7 | xxxxxxxx |
Indication | Engine speed | Engine charge signal | Road speed | Charge status → Note |
Indication field 05 - Mixture regulation - | ||||
Display | xxxx/min | 0…xxx % | 0,xx…1,xx | -xx,x…x,xx % |
Indication | Engine speed | Periodically supplies the active carbon filter solenoid valve 1 | Lambda correction factor | Mixture value correction |
|
Meaning if display = 1 | |||||||||
x | x | x | x | x | x | x | x | Indication group 01 | Indication group 04 |
1 | — | — | |||||||
1 | Idle switch, closed | — | |||||||
1 | — | — | |||||||
1 | Air conditioning compressor, connected | Enrichment for acceleration or full charge | |||||||
1 | Air conditioning, connected | Full charge identified | |||||||
1 | — | Partial charge identified | |||||||
1 | Reduction of engine torque → Note | Idle switch, closed | |||||||
1 | Engaged speed range | Cut off for deceleration, active |
4) | Identification should always be in 1. |