Fabia Mk2
| Summary of components of air conditioning unit |
| 1 - | Fresh air blower series resistor -N24- |
| q | removing and installing → Chapter |
| 2 - | Fresh air flap and re-circulating air flap control motor -V154- |
| q | with installed potentiometer -G143- |
| q | removing and installing → Chapter |
| q | check → Vehicle diagnostic, testing and information system VAS 5051 |
| 3 - | Fresh air blower -V2- |
| q | removing and installing → Chapter |
| 4 - | Trim panel of heater control |
| 5 - | Dust and pollen filter |
| q | also as combination filter with odour filter |
| q | removing and installing → Chapter |
| q | pay attention to change intervals → Booklet Roomster |
| 6 - | Flex shaft |
| q | for positioning unit for air distribution flaps |
| q | removing and installing → Chapter |
| 7 - | Control for heating and air conditioning system |
| q | Summary of components → Chapter |
| q | must be replaced completely |
| q | removing and installing → Chapter |
| 8 - | Plug for footwell vent temperature sender -G192- |
| q | no longer fitted as of CW 46.2010 |
| 9 - | Footwell vent temperature sender -G192- |
| q | not fitted on vehicles as of CW 46.2010 |
| q | to disassemble, remove centre console → Body Work; Rep. gr.68, release plug and turn sender 90° to the left |
| q | check → Vehicle diagnostic, testing and information system VAS 5051 |
| 10 - | O-ring |
| q | replace if damaged |
| 11 - | Heating element for air auxiliary heating -Z35- |
| q | only fitted on certain models |
| q | Summary of components → Chapter |
| q | removing and installing → Chapter |
| 12 - | Heat exchanger |
| q | Summary of components → Chapter |
| q | removing and installing → Chapter |
| 13 - | Positioning unit for temperature flap |
| q | up to CW 45.2010 - Control motor for temperature flap -V68- (flap operated via control motor) |
| – | with installed potentiometer for temperature flap control motor -G92- |
| – | Removing and installing control motor → Chapter |
| q | as of CW 46.2010, temperature flap mechanically operated via flex shaft |
| – | Remove and install the positioning unit for temperature flap → Chapter |
| – | Remove and install flex shaft → Chapter |
| 14 - | Gasket with holder |
| q | clipped at heater unit |
| q | replace if damaged |
| 15 - | Valve for condensation water drain |
| q | mount together with holder -Pos. 14- on air conditioning unit |
| 16 - | Plug for evaporator vent temperature sender -G263- |
| q | on right-hand drive vehicles, positioned on the right |
| 17 - | Middle vent temperature sender -G191- |
| q | not fitted on vehicles as of CW 46.2010 |
| q | installed in the intermediate piece for dash panel vents |
| q | to disassemble, remove damping trim panel below the left dash panel and footwell vent on the driver's side, turn sender 90° to the left, take out, lower and release plug |
| q | check → Vehicle diagnostic, testing and information system VAS 5051 |
| 18 - | Evaporator vent temperature sender -G263- |
| q | to disassemble, remove dash panel, release plug and pull out sideways |
| q | on right-hand drive vehicles, positioned on the right |
| q | check → Vehicle diagnostic, testing and information system VAS 5051 |
| 19 - | Sealing ring |
| q | replace if damaged |
| 20 - | Supports |
| q | for cooling the storage tray in the glove compartment |
| q | screwed onto housing |
| q | not fitted as of MY 2011 |
| 21 - | Connecting hose |
| q | to the storage tray in the glove compartment |
| q | not fitted as of MY 2011 |
