skoda Workshop Repair Guides

Skoda Workshop Service and Repair Manuals

ABOUT US
Bleed the clutch control > < Removing and installing the master cylinder (Fabia II 2011 ?; Roomster 2011 ?; Rapid)

Fabia Mk2

Removing and installing the slave cylinder
Removing and installing the slave cylinder
Special tools and workshop equipment required
t  Grease for plug serration of clutch disc -G 000 100-
Removing
  Note
After the battery earth strap is disconnected and re-connected, carry out additional operations → Electrical System; Rep. gr.27.
–  Remove engine cover → engine; Rep. gr.10.
–  Remove battery and battery tray → Electrical System; Rep. gr.27.
–  Remove air filter → Engine; Rep. gr.23.
   
–  Remove lock washer -arrow 1- for shift cable from gearbox shift lever -A-.
Vehicles Fabia II and Roomster up to 05.07, Vehicle Rapid (metal relay lever)
–  Remove circlip -arrow 2- for selector cable from relay lever -B-.
–  Remove selector cable and shift cable from the studs.
–  Detach circlip -arrow 3- from the relay lever -B- and remove relay lever.
Vehicles Fabia II and Roomster as of 06.07 (plastic relay lever)
–  Pull off shift cable from the stud.
–  Remove relay lever together with cable lock → Chapter.
Continued for all vehicles
–  Remove the gearshift lever -A-, for this step unscrew nut -arrow 4-.
  S30-0133
–  Disconnect the cable support from the gearbox (screws -1-).
–  Tie up shift cable and selector cable.
–  Place a non-fluffing cloth under the slave cylinder.
–  Pull retaining clip -2- for tube-hose line out of the slave cylinder up to the stop.
–  Then pull the tube-hose line -3- out of the slave cylinder and close openings.
–  Pull the tube-hose line -3- out of the bracket -4-, if present, on the gearbox.
–  Unscrew the screws -5- for the slave cylinder and remove the slave cylinder.
  Note
Do not depress the clutch pedal.
Install
Installation is performed in the reverse order, pay attention to the following points:
–  Grease tappet head with grease for plug serration of clutch disc -G 000 100 -.
  Note
t  Replace damaged gasket rings.
t  Assign all the components via the → Electronic Catalogue of Original Parts.
  S34-0502
–  Screw the slave cylinder onto the gearbox with the screws -5-.
–  Insert the tube-hose line -3- into the slave cylinder up to the stop.
–  Press in retaining clip -2- up to the stop.
–  Press the tube-hose line into the bracket -4-, if present, at the gearbox.
–  After installing the slave cylinder bleed the clutch control → Chapter.
–  Installing Bowden cable support, relay lever and gearshift lever.
For vehicles Fabia II and Roomster → Chapter
For vehicle Rapid → Chapter
–  Setting the shift mechanism.
For vehicles Fabia II and Roomster → Chapter
For vehicle Rapid → Chapter
–  Install air filter → Engine; Rep. gr.23.
–  Install the battery tray and battery → Electrical System; Rep. gr.27.
–  Connect earth strap of battery → Electrical System; Rep. gr.27.
  S34-0502
Tightening torque
ComponentTightening torque
Slave cylinder to gearboxFabia II, Roomster → Item
Rapid → Item
bracket for tube-hose lineFabia II, Roomster → Item
Rapid → Item
Cable support to gearbox → Chapter
Gearbox shift lever to gearbox → Chapter

   

Bleed the clutch control > < Removing and installing the master cylinder (Fabia II 2011 ?; Roomster 2011 ?; Rapid)