Octavia Mk2
|
| 1 - | Pressure control valve (PCV valve) |
| q | at timing case → Chapter |
| 2 - | Vacuum setting element for intake manifold flap |
| q | at fuel distributor (bottom part of intake manifold) → Chapter |
| 3 - | Intake manifold pressure sender -G71- and intake air temperature sender -G42- |
| q | on the intake manifold → Chapter |
| 4 - | Fuel pressure sender for low pressure -G410- |
| q | mounted up to 05.05 |
| q | in fuel feed line → Chapter |
| 5 - | Control valve for fuel pressure -N276- |
| q | to fuel-high pressure pump |
| 6 - | Motronic control unit -J220- |
| q | with integrated ambient pressure sender |
| q | in plenum chamber |
| q | removing and installing → Chapter |
| q | when replacing, clean throttle valve control unit -J338- → Chapter and adapt engine control unit to throttle valve control unit → Vehicle diagnosis, testing and information system VAS 5051 |
| 7 - | Solenoid valve 1 for activated charcoal filter -N80- |
| q | on the intake manifold → Chapter |
| 8 - | High pressure-fuel pump |
| q | on camshaft housing |
| q | removing and installing → Chapter |
| 9 - | Throttle valve control unit -J338- |
| q | with throttle valve drive for electronic power control -G186-, angle sensor 1 for throttle valve drive for electronic power control -G187- and angle sensor 2 for throttle valve drive for electronic power control -G188- |
| q | on intake manifold → Chapter |
| q | If replacing, adjust the engine control unit to the throttle valve control unit → Vehicle diagnosis, testing and information system VAS 5051 |
| q | clean throttle valve control unit -J338- → Chapter |
| 10 - | Exhaust gas recirculation valve -N18-°with exhaust gas recirculation potentiometer -G212- |
| q | at camshaft housing |
| q | removing and installing → Chapter |
| 11 - | Coolant temperature sender at radiator outlet -G83- |
| q | at bottom radiator connection fitting → Chapter |
| 12 - | Coolant temperature sender -G62- |
| q | in coolant regulator housing → Chapter |
| 13 - | 6-pin connector |
| q | for lambda probe -G39- and lambda probe heating before catalyst |
| 14 - | Hall sender -G40- |
| q | on camshaft housing → Chapter |
| 15 - | Lambda probe -G39- |
| q | after pre-catalytic converter → Chapter |
| 16 - | Ignition coils with a power output stage |
| q | Ignition coil 1 with a power output stage -N70- |
| q | Ignition coil 2 with a power output stage -N127- |
| q | Ignition coil 3 with a power output stage -N291- |
| q | Ignition coil 4 with a power output stage -N292- |
| q | removing and installing → Chapter |
| 17 - | Camshaft adjustment valve 1 -N205- |
| A - | Potentiometer for intake manifold flap -G336- |
| q | at fuel distributor (bottom part of intake manifold) → Chapter |
| B - | Intake manifold flap valve -N316- |
| q | on the intake manifold → Chapter |
| C - | Injection valves |
| q | Injection valve cylinder 1 -N30- |
| q | Injection valve cylinder 2 -N31- |
| q | Injection valve cylinder 3 -N32- |
| q | Injection valve cylinder 4 -N33- |
| q | in fuel distributor (bottom part of intake manifold) → Chapter |
| q | removing and installing → Chapter |
| D - | Engine speed sender -G28- |
| q | at sealing flange for crankshaft - gearbox side -, suction side |
| E - | Knock sensor 1 -G61- |
| q | at cylinder block suction side |
| q | removing and installing → Chapter |
| F - | Fuel pressure sender -G247 - |
| q | in fuel distributor (bottom part of intake manifold) → Chapter |
| G - | Intake air temperature sender 2 -G299- |
| q | in the engine cover with air filter → Chapter |
| H - | Accelerator pedal position sender - G79- and accelerator pedal position sender 2 -G185- |
| q | in footwell on the accelerator pedal (both senders are located in a housing) |
| I - | lambda probe downstream of catalytic converter -G130- |