skoda Workshop Repair Guides

Skoda Workshop Service and Repair Manuals

Intake manifold - Summary of components (Octavia II) > < Engine with identification characters BKC, BXE
Engine with identification characters BLS
Engine with identification characters BLS
Components A through G are not represented in the overview figure.
   
A - Warning light for engine electronics -K83-
q   on the dash panel insert
B - Accelerator pedal position sender -G79- with accelerator pedal position sender 2 -G185-
q   in footwell on the accelerator pedal
C - Brake light switch -F- and brake pedal switch -F47-
q   in footwell on the brake pedal
D - Fuel pump relay -J17-
q   on relay carrier
E - Clutch position sender -G476-
q   at master cylinder
F - Automatic glow period control unit -J179-
q   below E-box in the engine compartment
G - Relay and fuse carrier
q   with voltage supply relay of tml. 30 -J317 -
q   with voltage supply relay of tml. 15 -J329 -
q   E-box in the engine compartment
1 - Intake manifold flap motor -V157-
2 - Exhaust gas temperature sender 3 -G495- (Temperature sender downstream particle filter -G527-)
3 - Lambda probe -G39- with heating for lambda probe -Z19-
4 - Exhaust gas recirculation valve -N18- with EGR potentiometer -G212- and EGR control motor -V338-
5 - Engine control unit -J248 -
6 - Exhaust gas temperature sender 2 -G448- (Temperature sender upstream particle filter -G506-)
7 - Pressure sensor 1 for exhaust gas -G450-
8 - Exhaust gas temperature sender 1 -G235- (Temperature sender upstream turbocharger -G507 -)
9 - The unit injectors
q   Unit injector valve cyl. 1 -N240-
q   Unit injector valve cyl. 2 -N241-
q   Unit injector valve cyl. 3 -N242-
q   Unit injector valve cyl. 4 -N243-
q   Removing and installing unit injectors → Chapter
10 - Changeover valve for radiator of exhaust gas recirculation -N345-
11 - Coolant temperature sender -G62-
12 - Solenoid valve for charge pressure control -N75-
13 - Connector
q   on the left partition panel
q   Summary of components → Fig.
14 - Air mass meter -G70-
15 - Tandem pump
16 - Multipin plug connection
q   central for pump-nozzle units
17 - Engine speed sender -G28 -
q   removing and installing → Chapter
18 - Fuel temperature sender -G81-
19 - Glow plugs
q   Glow plug 3 -Q12-
q   Glow plug 4 -Q13-
q   removing and installing:
t  Metal glow plugs → Chapter.
t  Ceramic glow plugs → Chapter.
q   test:
t  Metal glow plugs → Chapter.
t  Ceramic glow plugs → Chapter.
20 - 3-pin plug
for hall sender -G40-
21 - Coolant temperature sender at radiator outlet -G83-
22 - Glow plugs
q   Glow plug 1 -Q10-
q   Glow plug 2 -Q11-
q   removing and installing:
t  Metal glow plugs → Chapter.
t  Ceramic glow plugs → Chapter.
q   test:
t  Metal glow plugs → Chapter.
t  Ceramic glow plugs → Chapter.
23 - Charge pressure sender -G31- with intake air temperature sender -G42-
24 - Hall sender -G40-
q   for camshaft position

   
Summary of components - plug on the partition wall
1 - Solenoid valve for charge pressure control -N75-
2 - Plug (orange) for temperature sender downstream particle filter -G527-
3 - Plug for temperature sender upstream particle filter -G506-
4 - Plug for lambda probe -G39- and heating for lambda probe -Z19-
5 - Plug for temperature sender upstream turbocharger -G507-
  A23-10003

Intake manifold - Summary of components (Octavia II) > < Engine with identification characters BKC, BXE