Octavia Mk2
| Fuel distributor - Summary of component |
| Vehicles up to 03.2006 |
| 1 - | Injection valve for cylinder 1 -N30- to injection valve for cylinder 4 -N33- |
| q | removing and installing → Chapter |
| 2 - | 5 Nm |
| 3 - | Fuel distributor |
| q | the fuel distributor must be removed together with the intake manifold |
| q | removing and installing → Chapter |
| 4 - | Plate nut |
| 5 - | Pressure limiting valve, 30 Nm |
| 6 - | Low pressure pipe |
Note| t | when removing, counterhold the pressure limiting valve |
| t | before installing, check that the pressure limiting valve has a tightening torque of 30 Nm |
| q | do not install under tension |
| q | Tighten union nut to 22 Nm |
| 7 - | Support |
| 8 - | High pressure pipe |
| q | do not install under tension |
| q | Tighten union nut at fuel distributor to 33 Nm |
| q | Tighten the union nut on the high pressure pump to 27 Nm. |
| 9 - | 3 Nm |
| 10 - | Connector |
| q | for injection valves |
| 11 - | Connector |
| q | for fuel pressure sender -G247- and Hall sender -G40- |
| 12 - | Connector |
| q | for injection valves |
| 13 - | Cable rail |
| 14 - | Retaining clip |
| q | hang at bottom right on sleeve of intake manifold |
| 15 - | Connector |
| q | for hall sender -G40- |
| 16 - | Connector |
| q | for fuel pressure sender -G247- |
| 17 - | 5 Nm |
| 18 - | Fuel pressure sender -G247-, 22 Nm |
| q | Moisten thread and sealing cone with clean engine oil |
| q | removing and installing → Chapter |
| q | check → Chapter |
| Vehicles as of 04.2006 |
| 1 - | Injection valve for cylinder 1 -N30- to injection valve for cylinder 4 -N33- |
| q | removing and installing → Chapter |
| 2 - | 5 Nm |
| 3 - | Fuel distributor |
| q | the fuel distributor must be removed together with the intake manifold |
| q | removing and installing → Chapter |
| 4 - | Low pressure fuel hose |
| q | to high pressure pump |
| 5 - | Pressure limiting valve, 30 Nm |
| 6 - | Plate nut |
| 7 - | Low pressure pipe |
Note| t | when removing, counterhold the pressure limiting valve |
| t | before installing, check that the pressure limiting valve has a tightening torque of 30 Nm |
| q | do not install under tension |
| q | Tighten union nut to 22 Nm |
| 8 - | Support |
| 9 - | High pressure pipe |
Note| t | when removing, counterhold the screw neck on the fuel distributor and on the high pressure pump |
| t | before installing, check that the screw neck on the fuel distributor has a tightening torque of 30 Nm |
| t | before installing, check that the screw neck on the high pressure pump has a tightening torque of 40 Nm |
| q | do not install under tension |
| q | Tighten the union nuts on the fuel distributor and on the high pressure pump to 27 Nm |
| 10 - | 3 Nm |
| 11 - | Connector |
| q | for injection valves |
| 12 - | Connector |
| q | for fuel pressure sender -G247- and Hall sender -G40- |
| 13 - | Connector |
| q | for injection valves |
| 14 - | Cable rail |
| 15 - | Retaining clip |
| q | hang at bottom right on sleeve of intake manifold |
| 16 - | Connector |
| q | for hall sender -G40- |
| 17 - | Connector |
| q | for fuel pressure sender -G247- |
| 18 - | 5 Nm |
| 19 - | Fuel pressure sender -G247-, 22 Nm |
| q | Moisten thread and sealing cone with clean engine oil |
| q | removing and installing → Chapter |
| q | check → Chapter |
| 20 - | Screw neck, 30 Nm |
