Octavia Mk2
| Summary of components - Control cables (Octavia ll) |
Note| Grease bearing and friction surfaces with grease -G 000 450 02-. |
| 1 - | Shift cable |
| q | connect with cable lock Pos. 18 |
| q | removing and installing → Chapter |
| q | Fitting position → Chapter |
| q | as of 11.06 modified attachment to the gearshift lever within the shift mechanism → Chapter |
| q | after installing set shift mechanism → Chapter |
| 2 - | Selector cable |
| q | connect with cable lock Pos. 11 |
| q | removing and installing → Chapter |
| q | Fitting position → Chapter |
| q | as of 11.06 modified attachment to the selector angle plate within the shift mechanism → Chapter |
| q | after installing set shift mechanism → Chapter |
| 3 - | Lock washer |
| q | always replace → Electronic Catalogue of Original Parts |
| q | no longer applicable → Chapter for shift mechanisms as of 11.06 |
| 4 - | Lock washer |
| q | do not damage cables when removing |
| q | always replace → Electronic Catalogue of Original Parts |
| 5 - | Shift housing |
| 6 - | 20 Nm |
| q | 2 pieces |
| q | for cable support |
| q | replace → Electronic Catalogue of Original Parts |
| 7 - | Cable support |
| q | made out of plastic or metal |
| 8 - | Grommet |
| q | Mounting of cable support to gearbox |
| 9 - | Spacer |
| 10 - | 20 Nm |
| q | for cable support |
| 11 - | Cable lock |
| q | for selector cable at relay lever |
| q | do not interchange, cable locks for selector cable at relay lever and for shift cable at gearshift lever are different |
| q | after installing set shift mechanism → Chapter |
| q | as of 06.07 it is fitted together with plastic relay lever → Chapter |
| q | remove from plastic relay lever → Chapter |
| q | press onto plastic relay lever → Chapter |
| q | Assignment → Fig. |
| 12 - | Reversing lever |
| q | Fitting position → Fig. |
| q | after installing set shift mechanism → Chapter |
| q | made out of plastic or metal |
| q | Metal relay lever is located in the bushings pos. 13 and secured with a lock washer pos. 14 |
| q | as of 06:07:00 plastic relay lever → Chapter |
| q | Removing and installing plastic relay lever together with cable lock → Chapter |
| q | Bushings pos. 13 and lock washer pos. 14 are not required for plastic relay lever |
| 13 - | Bushing |
| q | is not required, if the relay lever is made of plastic |
| 14 - | Lock washer |
| q | always replace → Electronic Catalogue of Original Parts |
| q | is not required, if the relay lever is made of plastic |
| 15 - | Sliding shoe |
| 16 - | Gearshift lever |
| q | with balancing weight |
| q | insert in such a way that the interrupted spacing of the teeth matches the gearshift shaft |
| q | after installing set shift mechanism → Chapter |
| q | Fitting position → Fig. |
| q | as of 06.06 smaller diameter of the mounting pin for the cable lock → Fig. |
| 17 - | 23 Nm |
| q | always replace → Electronic Catalogue of Original Parts |
| 18 - | Cable lock |
| q | for shift cable at gearbox shift lever |
| q | after installing set shift mechanism → Chapter |
| q | do not interchange, cable locks for selector cable at relay lever and for shift cable at gearshift lever are different |
| q | Assignment → Fig. |
|
|
| Cable lock for | Dimension „a“ |
| 1. - Shift cable at gearbox shift lever as of 06.06 | 8.5 mm |
| 2. - Shift cable at gearbox shift lever up to 05.06 | 10 mm |
| 2. - Selector cable at metal relay lever | 8 mm |
| 2. - Selector cable at plastic relay lever → Chapter | 10 mm |
|
|
| Mounting pin for the cable lock of the shift cable | Dimension „a“ |
| to 05.06 | 10 mm |
| from 06.06 | 8.5 mm |
