Superb
Overview of electric/electronic components and fitting locations |
1 - | Automatic gearbox control unit -J217- |
q | Fitting location → Fig. |
Note
If the engine or gearbox control units are replaced, the system must be put into the basic setting. |
q | removing → Fig. |
q | installing → Fig. |
q | can be checked in the “guided fault detection system” with → Vehicle diagnosis, testing and information system VAS 5051 |
2 - | Engine control unit |
q | Fitting location and removing and installing → Fig. |
Note
If the engine or gearbox control units are replaced, the system must be put into the basic setting. |
3 - | Diagnostic connection |
q | Fitting location → Fig. |
4 - | Wiring loom with gearbox oil temperature sender -G93- |
q | Fitting location → Fig. |
q | can be checked in the “guided fault detection system” with → Vehicle diagnosis, testing and information system VAS 5051 |
q | removing and installing → Chapter |
5 - | Slide valve body |
q | Fitting location → Fig. |
q | can be checked in the “guided fault detection system” with → Vehicle diagnosis, testing and information system VAS 5051 |
q | removing and installing → Chapter |
6 - | Multi-function switch -F125- |
q | Fitting location → Fig. |
q | removing and installing → Chapter |
q | can be checked in the “guided fault detection system” with → Vehicle diagnosis, testing and information system VAS 5051 |
7 - | Gearbox input r.p.m. sender -G182 - |
q | detects the gearbox input r.p.m. |
q | Fitting location → Fig. |
q | removing and installing → Chapter |
q | can be checked in the “guided fault detection system” with → Vehicle diagnosis, testing and information system VAS 5051 |
8 - | Gearbox speed sender -G38-/Gearbox output r.p.m. sender -G195- |
q | detects the gearbox output r.p.m. |
q | Fitting location → Fig. |
q | removing and installing → Chapter |
q | can be checked in the “guided fault detection system” with → Vehicle diagnosis, testing and information system VAS 5051 |
9 - | Switch for Tiptronic -F189- |
q | Fitting location → Fig. |
q | if the switch is faulty, the display symbol insert and circuit board must be replaced |
q | removing and installing → Chapter |
q | can be checked in the “guided fault detection system” with → Vehicle diagnosis, testing and information system VAS 5051 |
10 - | Selector lever lock solenoid -N110- |
q | Fitting location → Fig. |
q | removing and installing → Chapter |
q | can be checked in the “guided fault detection system” with → Vehicle diagnosis, testing and information system VAS 5051 |
11 - | Accelerator pedal position sender -G79- |
q | Other information → Fig. |
q | can be checked in the “guided fault detection system” with → Vehicle diagnosis, testing and information system VAS 5051 |
12 - | Switch for cruise control system - E45- |
q | Fitting location → Fig. |
q | can be checked in the “guided fault detection system” with → Vehicle diagnosis, testing and information system VAS 5051 |
13 - | Relay for starter interlock switch -J207- |
q | Fitting location → Fig. |
14 - | Selector lever position indicator -Y6- |
q | Fitting location → Fig. |
q | All parts of the selector lever position display are lit at the same time, or no selector lever position indicator indicates that the gearbox is in emergency mode |
15 - | Kickdown switch -F8- |
q | Fitting location → Fig. |
q | can be checked in the “guided fault detection system” with → Vehicle diagnosis, testing and information system VAS 5051 |
16 - | Brake light switch -F- or Brake pedal switch -F47- |
q | Fitting location and removing and installing → Fig. |
q | can be checked in the “guided fault detection system” with → Vehicle diagnosis, testing and information system VAS 5051 |