|
Result
|
Cause Of Fault
|
|
E001
|
Result: Defective Component
|
- Defective component:
B175 Sensor - Pressure, Exhaust Gas
Note:
Check the hoses for leakage or blockage before replacing the component.
After replacing the following component the programming function for the replacement of the corresponding component has to be performed by using the diagnostic tester:
B175 Sensor - Pressure, Exhaust Gas
|
|
|
|
E002
|
Result: Defective Component
|
- Defective component:
B175 Sensor - Pressure, Exhaust Gas
Important:
Check the hoses for leakage or blockage before replacing the component.
After replacing the following component the programming function for the replacement of the corresponding component has to be performed by using the diagnostic tester:
B175 Sensor - Pressure, Exhaust Gas
|
|
|
|
E003
|
Result: Interruption
|
- Circuit interruption between:
B175 Sensor - Pressure, Exhaust Gas
Wiring harness connector (wiring harness side) terminal 3
&
A84 Control Unit - Engine
Wiring harness connector (wiring harness side) terminal 39 (XC97)
or
- Defective component:
A84 Control Unit - Engine
Important:
Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
|
|
|
|
E004
|
Result: Short to Ground
|
- Short circuit to ground between:
B175 Sensor - Pressure, Exhaust Gas
Wiring harness connector (wiring harness side) terminal 3
&
A84 Control Unit - Engine
Wiring harness connector (wiring harness side) terminal 39 (XC97)
or
- Defective component:
A84 Control Unit - Engine
Important:
Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
|
|
|
|
E005
|
Result: Short to Voltage
|
- Short circuit to voltage between:
B175 Sensor - Pressure, Exhaust Gas
Wiring harness connector (wiring harness side) terminal 3
&
A84 Control Unit - Engine
Wiring harness connector (wiring harness side) terminal 39 (XC97)
or
- Defective component:
A84 Control Unit - Engine
Important:
Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
|
|
|
|
E006
|
Result: Short to Voltage/Ground/Interruption
|
- Short to voltage/ground/interruption of circuit between:
B175 Sensor - Pressure, Exhaust Gas
Wiring harness connector (wiring harness side) terminal 2
&
A84 Control Unit - Engine
Wiring harness connector (wiring harness side) terminal 15 (XC97)
or
- Defective component:
A84 Control Unit - Engine
Important:
Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
|
|
|
|
E007
|
Result: Short to Voltage/Interruption
|
- Circuit interruption between:
B175 Sensor - Pressure, Exhaust Gas
Wiring harness connector (wiring harness side) terminal 1
&
A84 Control Unit - Engine
Wiring harness connector (wiring harness side) terminal 63 (XC97)
or
- Defective component:
A84 Control Unit - Engine
Important:
Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
|
|
|
