vauxhall Workshop Repair Guides

Vauxhall Workshop Service and Repair Manuals

ABOUT US
C-005 Throttle Position Sensor Circuit > < C-003 Fuel Pump Relay Circuit

Astra H

C-004 - Pedal Position Sensor Circuit

Test

Work Order Description

Nominal Value
T001

Check: Short to Voltage/Ground/Interruption of Voltage Supply
  • Ignition OFF
  • Disconnect wiring harness connector from:
    B22 Sensor - Pedal Position
  • Ignition ON
  • Measure voltage between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    Ground

4.8 ... 5.2 V
Voltage Measurement Current Value: V
Yes: No:
T002

Check: Short to Voltage/Interruption of Ground Circuit
  • Measure voltage between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 5

4.8 ... 5.2 V
Voltage Measurement Current Value: V
Yes: No:
T003

Check: Short to Voltage/Ground/Interruption of Voltage Supply
  • Measure voltage between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 2
    &
    Ground

4.8 ... 5.2 V
Voltage Measurement Current Value: V
Yes: No:
T004

Check: Short to Voltage/Interruption of Ground Circuit
  • Measure voltage between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 2
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 4

4.8 ... 5.2 V
Voltage Measurement Current Value: V
Yes: No:
T005

Check: Short to Voltage of Signal Circuit
  • Diagnostic Tester Data List Parameter
    APP Sensor 1 (Accelerator Pedal Position)

less than 0.3 V
Diagnostic Tester Data List Parameter Current Value:
Yes: No:
T006

Check: Short to Voltage of Signal Circuit
  • Diagnostic Tester Data List Parameter
    APP Sensor 2 (Accelerator Pedal Position)

less than 0.3 V
Diagnostic Tester Data List Parameter Current Value:
Yes: No:
T007

Check: Short to Ground/Interruption of Signal Circuit
  • Connect fused jumper wire to:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 2
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 6
  • Diagnostic Tester Data List Parameter
    APP Sensor 2 (Accelerator Pedal Position)

greater than 4.8 V
Diagnostic Tester Data List Parameter Current Value:
Yes: No:
T008

Check: Short to Ground/Interruption of Signal Circuit
  • Remove fused jumper wire
  • Connect fused jumper wire to:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 2
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 3
  • Diagnostic Tester Data List Parameter
    APP Sensor 1 (Accelerator Pedal Position)

greater than 4.8 V
Diagnostic Tester Data List Parameter Current Value:
Yes: No:
T009

Check: Short to Ground/Interruption of Signal Circuit
  • Remove fused jumper wire
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector (XC8) )
  • Measure resistance between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 3
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T010

Check: Interruption of Signal Circuit
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 54 (XC8)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 3

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T011

Check: Interruption of Signal Circuit
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2, XE3 )
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 54 (XC8)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 44 (XE3)

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T012

Check: Short to Ground/Interruption of Signal Circuit
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2, XE3 )
  • Measure resistance between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 3
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T013

Check: Short to Ground/Interruption of Signal Circuit
  • Remove fused jumper wire
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector (XC8) )
  • Measure resistance between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 6
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T014

Check: Interruption of Signal Circuit
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 37 (XC8)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 6

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T015

Check: Interruption of Signal Circuit
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2, XE3 )
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 37 (XC8)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 35 (XE3)

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T016

Check: Short to Ground/Interruption of Signal Circuit
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2, XE3 )
  • Measure resistance between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 6
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T017

Check: Short to Voltage of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector (XC8) )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 37 (XC8)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T018

Check: Short to Voltage of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2, XE3 )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 37 (XC8)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T019

Check: Short to Voltage of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector (XC8) )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 54 (XC8)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T020

Check: Short to Voltage of Signal Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2, XE3 )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 54 (XC8)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T021

Check: Short to Voltage of Ground Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    M3A Motor - Radiator Fan
    M3B Motor - Radiator Fan
    and
    A84 Control Unit - Engine
    (Wiring Harness Connector (XC8) )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 22 (XC8)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T022

Check: Circuit Interruption of Ground Circuit
  • Ignition OFF
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 22 (XC8)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 4

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T023

Check: Circuit Interruption of Ground Circuit
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2, XE3 )
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 22 (XC8)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 37 (XE3)

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T024

Check: Short to Voltage of Ground Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2, XE3 )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 22 (XC8)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T025

Check: Short to Voltage/Ground/Interruption of Voltage Supply
  • Measure voltage between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 2
    &
    Ground

greater than 5.2 V
Voltage Measurement Current Value: V
Yes: No:
T026

Check: Short to Voltage of Voltage Supply Circuit
  • Ignition OFF
  • Remove electrical component from socket:
    K12_X125 Relay - Radiator Fan
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector (XC7) )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 56 (XC7)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T027

Check: Short to Voltage of Voltage Supply Circuit
  • Ignition OFF
  • Connect wiring harness connector to:
    A84 Control Unit - Engine
    (Wiring Harness Connector (XC7) )
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector (XC8) )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 21 (XC8)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T028

Check: Short to Voltage of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2, XE3 )
  • Ignition ON
  • Measure voltage between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 21 (XC8)
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T029

Check: Short to Ground/Interruption of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    M3A Motor - Radiator Fan
    M3B Motor - Radiator Fan
    and
    A84 Control Unit - Engine
    (Wiring Harness Connector (XC7) )
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 56 (XC7)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T030

Check: Interruption of Voltage Supply Circuit
  • Connect wiring harness connector to:
    A84 Control Unit - Engine
    (Wiring Harness Connector (XC7) )
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector (XC8) )
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 21 (XC8)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T031

Check: Interruption of Voltage Supply Circuit
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 21 (XC8)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 2

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T032

Check: Interruption of Voltage Supply Circuit
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2, XE3 )
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 21 (XC8)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 36 (XE3)

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T033

Check: Interruption of Voltage Supply Circuit
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2, XE3 )
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 21 (XC8)
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T034

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Astra-H, Electronic Climate Control ECC
Astra-H, Air Conditioning (not ECC)
Astra-H, Automatic Climate Control SAC
Yes: No:
T035

Check: Short to Voltage/Interruption of Ground Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    B18 Sensor - Pressure, Air Conditioning
  • Ignition ON
  • Measure voltage between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    Wiring harness connector (wiring harness side) terminal 5

4.8 ... 5.2 V
Voltage Measurement Current Value: V
Yes: No:
T036

Check: Short to Voltage of Ground Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector (XC8) )
  • Ignition ON
  • Measure voltage between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 5
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T037

Check: Circuit Interruption of Ground Circuit
  • Ignition OFF
  • Measure resistance between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 5
    &
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 5 (XC8)

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T038

Check: Circuit Interruption of Ground Circuit
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2, XE3 )
  • Measure resistance between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 5
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 18 (XE2)

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T039

Check: Short to Voltage of Ground Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2, XE3 )
  • Ignition ON
  • Measure voltage between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 5
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T040

Check: Short to Voltage/Ground/Interruption of Voltage Supply
  • Ignition OFF
  • Disconnect wiring harness connector from:
    B22 Sensor - Pedal Position
  • Ignition ON
  • Measure voltage between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    Ground

less than 4.8 V
Voltage Measurement Current Value: V
Yes: No:
T041

Check: Short to Ground/Interruption of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    B69 Air Mass Meter
  • Ignition ON
  • Measure voltage between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    Ground
  • Disconnect each of the following components/control units consecutively from the wiring harness and repeat the measurement each time:
    B28 Sensor - Camshaft
    B150 Sensor - Boost Pressure
    B26 Sensor - Atmospheric Pressure

4.8 ... 5.2 V
Voltage Measurement Current Value: V
Yes: No:
T042

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Astra-H, Electronic Climate Control ECC
Astra-H, Air Conditioning (not ECC)
Astra-H, Automatic Climate Control SAC
Yes: No:
T043

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    B18 Sensor - Pressure, Air Conditioning
  • Ignition ON
  • Measure voltage between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    Ground

4.8 ... 5.2 V
Voltage Measurement Current Value: V
Yes: No:
T044

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    M3A Motor - Radiator Fan
    M3B Motor - Radiator Fan
    and
    A84 Control Unit - Engine
    (Wiring Harness Connector (XC7, XC8) )
  • Measure resistance between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T045

Check: Interruption of Voltage Supply Circuit
  • Measure resistance between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 4 (XC7)

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T046

Check: Interruption of Voltage Supply Circuit
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2, XE3 )
  • Measure resistance between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 17 (XE2)

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T047

Check: Short to Ground of Voltage Supply Circuit
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2, XE3 )
  • Measure resistance between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T048

Check: Short to Voltage of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    B69 Air Mass Meter
  • Ignition ON
  • Measure voltage between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    Ground
  • Disconnect each of the following components/control units consecutively from the wiring harness and repeat the measurement each time:
    B28 Sensor - Camshaft
    B150 Sensor - Boost Pressure
    B26 Sensor - Atmospheric Pressure

4.8 ... 5.2 V
Voltage Measurement Current Value: V
Yes: No:
T049

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Astra-H, Electronic Climate Control ECC
Astra-H, Air Conditioning (not ECC)
Astra-H, Automatic Climate Control SAC
Yes: No:
T050

Check: Short to Voltage of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    B18 Sensor - Pressure, Air Conditioning
  • Ignition ON
  • Measure voltage between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    Ground

4.8 ... 5.2 V
Voltage Measurement Current Value: V
Yes: No:
T051

Check: Short to Voltage of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    M3A Motor - Radiator Fan
    M3B Motor - Radiator Fan
    and
    A84 Control Unit - Engine
    (Wiring Harness Connector (XC7, XC8) )
  • Ignition ON
  • Measure voltage between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T052

Check: Short to Voltage of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    X125 Underhood Electronic Module
    (Wiring Harness Connector XE2, XE3 )
  • Ignition ON
  • Measure voltage between the following terminals:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:


Result

Cause Of Fault
E001 Result: Defective Component
  • Defective component:
    B22 Sensor - Pedal Position
    or
    A84 Control Unit - Engine

Note:

The replacement of the components must be done in the listed order.

The system must be checked for proper operation after every replacement.

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E002 Result: Defective Component
  • Defective component:
    A84 Control Unit - Engine

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E003 Result: Interruption
  • Circuit interruption between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 19 (XE2)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 3

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E004 Result: Interruption
  • Circuit interruption between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 54 (XC8)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 44 (XE3)
E005 Result: Short to Ground
  • Short circuit to ground between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 54 (XC8)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 44 (XE3)

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E006 Result: Short to Ground
  • Short circuit to ground between:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 3
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 19 (XE2)
E007 Result: Interruption
  • Circuit interruption between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 3 (XE2)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 6

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E008 Result: Interruption
  • Circuit interruption between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 37 (XC8)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 35 (XE3)
E009 Result: Short to Ground
  • Short circuit to ground between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 37 (XC8)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 35 (XE3)

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E010 Result: Short to Ground
  • Short circuit to ground between:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 6
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 3 (XE2)
E011 Result: Short to Voltage
  • Short circuit to voltage between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 3 (XE2)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 6
    &
    Concerned terminals of all wiring harness connectors, which are connected with the corresponding lead.

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E012 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 37 (XC8)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 35 (XE3)
    &
    Concerned terminals of all wiring harness connectors, which are connected with the corresponding lead.
E013 Result: Short to Voltage
  • Short circuit to voltage between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 19 (XE2)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 3
    &
    Concerned terminals of all wiring harness connectors, which are connected with the corresponding lead.

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E014 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 54 (XC8)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 44 (XE3)
    &
    Concerned terminals of all wiring harness connectors, which are connected with the corresponding lead.
E015 Result: Interruption
  • Circuit interruption between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 5 (XE2)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 4

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E016 Result: Interruption
  • Circuit interruption between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 22 (XC8)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 37 (XE3)
E017 Result: Short to Voltage
  • Short circuit to voltage between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 5 (XE2)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 4
    &
    Concerned terminals of all wiring harness connectors, which are connected with the corresponding lead.

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E018 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 22 (XC8)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 37 (XE3)
    &
    Concerned terminals of all wiring harness connectors, which are connected with the corresponding lead.
E019 Result: Short to Voltage
  • Short circuit to voltage between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 4 (XE2)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 2
    &
    Concerned terminals of all wiring harness connectors, which are connected with the corresponding lead.

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E020 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 21 (XC8)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 36 (XE3)
    &
    Concerned terminals of all wiring harness connectors, which are connected with the corresponding lead.
E021 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 56 (XC7)
    &
    A111 Throttle Valve - Positioner
    Wiring harness connector (wiring harness side) terminal 3

or

  • Defective component:
    A111 Throttle Valve - Positioner
E022 Result: Short to Ground/Interruption
  • Defective component:
    A84 Control Unit - Engine

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E023 Result: Interruption
  • Circuit interruption between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 4 (XE2)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 2

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E024 Result: Interruption
  • Circuit interruption between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 21 (XC8)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 36 (XE3)
E025 Result: Short to Ground
  • Short circuit to ground between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 4 (XE2)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 2
    &
    Concerned terminals of all wiring harness connectors, which are connected with the corresponding lead.

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E026 Result: Short to Ground
  • Short circuit to ground between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 21 (XC8)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 36 (XE3)
    &
    Concerned terminals of all wiring harness connectors, which are connected with the corresponding lead.
E027 Result: Short to Ground
  • Short circuit to ground between:
    A111 Throttle Valve - Positioner
    Wiring harness connector (wiring harness side) terminal 3
    &
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 56 (XC7)

or

  • Defective component:
    A111 Throttle Valve - Positioner
E028 Result: Defective Component
  • Defective component:
    B18 Sensor - Pressure, Air Conditioning
E029 Result: Defective Component
  • Defective component:
    A84 Control Unit - Engine

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E030 Result: Interruption
  • Circuit interruption between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 5 (XC8)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 43 (XE3)

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E031 Result: Interruption
  • Circuit interruption between:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 5
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 18 (XE2)
E032 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 5 (XC8)
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 43 (XE3)
    &
    Concerned terminals of all wiring harness connectors, which are connected with the corresponding lead.

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E033 Result: Short to Voltage
  • Short circuit to voltage between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 18 (XE2)
    &
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 5
    &
    Concerned terminals of all wiring harness connectors, which are connected with the corresponding lead.
E034 Result: Defective Component
  • If the nominal value is reached during one of the measurements, the component/control unit that has been disconnected immediately before that measurement is defective.
E035 Result: Defective Component
  • Defective component:
    B18 Sensor - Pressure, Air Conditioning
E036 Result: Short to Ground
  • Short circuit to ground between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 24 (XC7)
    &
    B69 Air Mass Meter
    Wiring harness connector (wiring harness side) terminal 4
    or
    B28 Sensor - Camshaft
    Wiring harness connector (wiring harness side) terminal 3
    &
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 3 (XC7)
    &
    Concerned terminals of all wiring harness connectors, which are connected with the corresponding lead.

or

  • Defective component:
    A84 Control Unit - Engine

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E037 Result: Short to Ground/Interruption
  • Circuit interruption between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 42 (XE3)
    &
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 4 (XC8)

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E038 Result: Interruption
  • Circuit interruption between:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 17 (XE2)
E039 Result: Short to Ground
  • Short circuit to ground between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 42 (XE3)
    &
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 4 (XC8)

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E040 Result: Short to Ground
  • Short circuit to ground between:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 17 (XE2)
E041 Result: Defective Component
  • Defective component:
    B18 Sensor - Pressure, Air Conditioning
E042 Result: Short to Voltage
  • Short circuit to voltage between:
    B28 Sensor - Camshaft
    Wiring harness connector (wiring harness side) terminal 2
    &
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 21 (XC7)
    &
    Concerned terminals of all wiring harness connectors, which are connected with the corresponding lead.

or

  • Defective component:
    A84 Control Unit - Engine

Important:

During the model year 2007 the wiring harness connector terminal 1 of the component B28 changes to terminal 2 (refer to wiring schematic diagram).

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E043 Result: Short to Voltage
  • Short circuit to voltage between:
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 42 (XE3)
    &
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 4 (XC8)
    &
    Concerned terminals of all wiring harness connectors, which are connected with the corresponding lead.

or

  • Defective component:
    X125 Underhood Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E044 Result: Short to Voltage
  • Short circuit to voltage between:
    B22 Sensor - Pedal Position
    Wiring harness connector (wiring harness side) terminal 1
    &
    X125 Underhood Electronic Module
    Wiring harness connector (wiring harness side) terminal 17 (XE2)
    &
    Concerned terminals of all wiring harness connectors, which are connected with the corresponding lead.





C-005 Throttle Position Sensor Circuit > < C-003 Fuel Pump Relay Circuit