Test
|
Work Order Description
|
Nominal Value
|
T001
|
Tester Display Battery Voltage
|
- Ignition ON
- Engine OFF
- All consumers turned off
Note:
This data list parameter is in the data list 1 .
|
11 ... 13.5 V
|
- Engine running at idle speed, operating temperature
- Accelerator pedal not actuated
|
12 ... 15 V
|
Concerned Terminals: 19, 33, 49 (XC98)
|
|
|
T002
|
Tester Display Fuel Pump Relay
|
- Ignition ON
- Engine OFF
- All consumers turned off
Note:
This data list parameter is in the data list 1 .
|
Inactive
|
- Engine running at idle speed, operating temperature
- Accelerator pedal not actuated
|
Active
|
Concerned Terminals: 36 (XC98)
|
|
|
T003
|
Tester Display APP at Idle Position (Accelerator Pedal Position)
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 1 .
|
Active
|
- Accelerator pedal slightly actuated
|
Inactive
|
Concerned Terminals: 4, 5, 21, 22, 37, 54 (XC98)
|
|
|
T004
|
Tester Display APP Sensor 1 (Accelerator Pedal Position)
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 1 .
|
0.9 ... 1.1 V
|
- Accelerator pedal slightly actuated
|
greater than 1.1 V
|
- Accelerator pedal actuated to full load stop
|
3.5 ... 4.2 V
|
Concerned Terminals: 4, 5, 21, 22, 37, 54 (XC98)
|
|
|
T005
|
Tester Display APP Sensor 2 (Accelerator Pedal Position)
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 1 .
|
0.45 ... 0.55 V
|
- Accelerator pedal slightly actuated
|
greater than 0.6 V
|
- Accelerator pedal actuated to full load stop
|
1.75 ... 2.1 V
|
Concerned Terminals: 4, 5, 21, 22, 37, 54 (XC98)
|
|
|
T006
|
Tester Display Calculated Pedal Position
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 1, 2 .
|
0 %
|
- Accelerator pedal actuated to full load stop
|
greater than 90 %
|
Concerned Terminals: 4, 5, 21, 22, 37, 54 (XC98)
|
|
|
T007
|
Tester Display TP Sensor 1 (Throttle Position)
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Accelerator pedal not actuated
- Wait time: minimum 15 s
Note:
This data list parameter is in the data list 1 .
|
0.4 ... 1.2 V
|
- Accelerator pedal actuated to full load stop
|
4.0 ... 4.8 V
|
Concerned Terminals: 23, 39, 56, 58 (XC99)
|
|
|
T008
|
Tester Display TP Sensor 2 (Throttle Position)
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Accelerator pedal not actuated
- Wait time: minimum 15 s
Note:
This data list parameter is in the data list 1 .
|
3.8 ... 4.6 V
|
- Accelerator pedal actuated to full load stop
|
0.2 ... 1.0 V
|
Concerned Terminals: 23, 39, 56, 58 (XC99)
|
|
|
T009
|
Tester Display Calculated Throttle Position
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Accelerator pedal not actuated
- Wait time: minimum 15 s
Note:
This data list parameter is in the data list 1, 2 .
|
0 ... 9 %
|
- Accelerator pedal actuated to full load stop
|
greater than 90 %
|
Concerned Terminals: 23, 39, 56, 58 (XC99)
|
|
|
T010
|
Tester Display Throttle Position PWM Servo Signal
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 1, 2 .
|
8 ... 100 %
|
Concerned Terminals: 23, 39, 56, 58 (XC99)
|
|
|
T011
|
Tester Display Throttle Position
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Accelerator pedal not actuated
- Wait time: minimum 15 s
Note:
This data list parameter is in the data list 1, 2 .
|
Idle
|
- Accelerator pedal slightly actuated
|
Partial Load
|
- Accelerator pedal actuated to full load stop
|
Full Load
|
Concerned Terminals: 23, 39, 56, 58 (XC99)
|
|
|
T012
|
Tester Display Desired Engine Idle Speed
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 1 .
|
750 ... 950 rpm
This parameter is an internal value of the control unit.
|
Concerned Terminals: -
|
|
|
T013
|
Tester Display Engine Speed
|
Note:
This data list parameter is in the data list 1 .
|
greater than 60 RPM.
|
Concerned Terminals: 3, 21, 27 (XC99)
|
|
|
T014
|
Tester Display Mass Air Flow Sensor
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 1, 2 .
|
less than 16 kg/h
less than 1.8 V
|
Concerned Terminals: 6, 24, 26 (XC99)
|
|
|
T015
|
Tester Display Barometric Pressure
|
- Ignition ON
- Engine OFF
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 1 .
|
90 ... 110 kPa
Diagnostic tester display is nearly identical to outside-air pressure
|
Concerned Terminals: 7, 10, 60 (XC99)
|
|
|
T016
|
Tester Display Boost Pressure
|
- Ignition ON
- Engine OFF
- All consumers turned off
Note:
This data list parameter is in the data list 1, 2 .
|
90 ... 110 kPa
0.6 ... 0.9 V
|
Concerned Terminals: 7, 22 (XC99)
|
|
|
T017
|
Tester Display Intake Air Temperature
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 1 .
|
10 ... 40 °C
50 ... 104 °F
4.1 ... 2.6 V
|
Concerned Terminals: 9, 55 (XC99)
|
|
|
T018
|
Tester Display Coolant Temperature
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 1 .
|
greater than 80 °C
greater than 176 °F
less than 1.25 V
|
Concerned Terminals: 38, 42 (XC99)
|
|
|
T019
|
Tester Display Oil Level
|
- Ignition ON
- Engine OFF
- All consumers turned off
Note:
This data list parameter is in the data list 1 .
|
Normal
|
- Engine running at idle speed, operating temperature
- Accelerator pedal not actuated
|
Normal
|
Concerned Terminals: 40 (XC99)
|
|
|
T020
|
Tester Display Oil Pressure
|
- Ignition ON
- Engine OFF
- All consumers turned off
Note:
This data list parameter is in the data list 1 .
|
Low Pressure
|
|
Normal
|
Concerned Terminals: 5 (XC99)
|
|
|
T021
|
Tester Display Engine Oil Level Status
|
- Ignition ON
- Engine OFF
- All consumers turned off
Note:
This data list parameter is in the data list 1 .
|
Okay
|
- Engine running at idle speed, operating temperature
- Accelerator pedal not actuated
|
Okay
|
Concerned Terminals: 40 (XC99)
|
|
|
T022
|
Tester Display A/C Information Switch (Air Conditioning)
|
- Ignition ON
- Air conditioning system switch OFF
Note:
This data list parameter is in the data list 1 .
|
|
Default
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Air Conditioning (not ECC))
|
Inactive
|
(Electronic Climate Control ECC)
|
Inactive
|
(Automatic Climate Control SAC)
|
Inactive
|
- Engine running at idle speed, operating temperature
- Air conditioning system is switched on.
|
|
Default
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Air Conditioning (not ECC))
|
Active
|
(Electronic Climate Control ECC)
|
Active
|
(Automatic Climate Control SAC)
|
Active
|
Concerned Terminals: 5, 30, 39, 53 (XC98)
|
|
|
T023
|
Tester Display A/C Pressure (Air Conditioning)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 1 .
|
|
Default
|
0 kPa
The data list parameter is invalid for this configuration
|
(Air Conditioning (not ECC))
|
320 ... 3100 kPa
|
(Electronic Climate Control ECC)
|
320 ... 3100 kPa
|
(Automatic Climate Control SAC)
|
320 ... 3100 kPa
|
- Air conditioning system is switched on.
|
|
Default
|
0 kPa
The data list parameter is invalid for this configuration
|
(Air Conditioning (not ECC))
|
greater than 0 kPa
Is there a pressure difference of at least 500 kPa ?
|
(Electronic Climate Control ECC)
|
greater than 0 kPa
Is there a pressure difference of at least 500 kPa ?
|
(Automatic Climate Control SAC)
|
greater than 0 kPa
Is there a pressure difference of at least 500 kPa ?
|
Concerned Terminals: 5, 30, 39, 53 (XC98)
|
|
|
T024
|
Tester Display A/C Cutoff Mode (Air Conditioning)
|
- Ignition ON
- Engine OFF
- All consumers turned off
Note:
This data list parameter is in the data list 1 .
|
|
Default
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Air Conditioning (not ECC))
|
System OK
|
(Electronic Climate Control ECC)
|
System OK
|
(Automatic Climate Control SAC)
|
System OK
|
Concerned Terminals: 5, 30, 39, 53 (XC98)
|
|
|
T025
|
Tester Display A/C Relay (Air Conditioning)
|
- Ignition ON
- Air conditioning system switch OFF
Note:
This data list parameter is in the data list 1 .
|
|
Default
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Air Conditioning (not ECC))
|
Inactive
|
(Electronic Climate Control ECC)
|
Inactive
|
(Automatic Climate Control SAC)
|
Inactive
|
- Engine running at idle speed, operating temperature
- Air conditioning system is switched on.
|
|
Default
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Air Conditioning (not ECC))
|
Active
|
(Electronic Climate Control ECC)
|
Active
|
(Automatic Climate Control SAC)
|
Active
|
Concerned Terminals: 5, 30, 39, 53 (XC98)
|
|
|
T026
|
Tester Display Brake Switch 1
|
- Ignition ON
- Engine OFF
- All consumers turned off
Note:
This data list parameter is in the data list 1 .
|
Inactive
|
|
Active
|
Concerned Terminals: 25 (XC98)
|
|
|
T027
|
Tester Display Brake Switch 2
|
- Ignition ON
- Engine OFF
- All consumers turned off
Note:
This data list parameter is in the data list 1 .
|
Inactive
|
|
Active
|
Concerned Terminals: 25 (XC98)
|
|
|
T028
|
Tester Display Clutch Switch
|
Vehicle with manual transmission:
- Ignition ON
- Engine OFF
- All consumers turned off
- Do not actuate clutch pedal
Note:
This data list parameter is in the data list 1 .
|
|
Default
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Electronic Cruise Control)
|
Inactive
|
|
|
Default
|
Not Programmed
The data list parameter is invalid for this configuration
|
(Electronic Cruise Control)
|
Active
|
Concerned Terminals: 8 (XC98)
|
|
|
T029
|
Tester Display Vehicle Speed
|
- Vehicle travelling (constant speed, approximately 30 km/h (19 mph))
Note:
This data list parameter is in the data list 1 .
|
Diagnostic tester display is nearly identical to actual vehicle speed
|
Concerned Terminals: -
|
|
|
T030
|
Tester Display Cruise Control Tip Switch
|
- Engine running at idle speed, operating temperature
- Brake pedal actuated
- Vehicle stationary
- Key " I " not pressed
Note:
This data list parameter is in the data list 1 .
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
Inactive
|
- Key " I " pressed briefly
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
I (set)
|
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
Inactive
|
- Key " R " pressed briefly
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
R (Resume)
|
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
Inactive
|
- Key " O " pressed briefly
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
O (off)
|
- Key " R+O " pressed briefly
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
Not Programmed
|
- Vehicle travelling (constant speed, approximately 40 km/h (25 mph))
- Brake pedal not actuated
- Clutch pedal not actuated/selector lever in position D
- Cruise control active
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
Active
|
Concerned Terminals: -
|
|
|
T031
|
Tester Display Cruise Control
|
- Engine running at idle speed, operating temperature
- Brake pedal actuated
- Vehicle stationary
- Key " I " not pressed
Note:
This data list parameter is in the data list 1 .
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
Inactive
|
- Vehicle travelling (constant speed, approximately 40 km/h (25 mph))
- Brake pedal not actuated
- Clutch pedal not actuated/selector lever in position D
- Cruise control active
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
Active
|
Concerned Terminals: -
|
|
|
T032
|
Tester Display Vehicle Speed in Cruise Control Range
|
- Vehicle speed is greater than 30 km/h (19 mph)
Note:
This data list parameter is in the data list 1 .
|
|
Default
|
Not Programmed
|
(Electronic Cruise Control)
|
Active
|
Concerned Terminals: -
|
|
|
T033
|
Tester Display Fuel Tank Ventilation Valve
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 1 .
|
Inactive
0 %
Value changing briefly
|
- Vehicle travelling (constant speed, approximately 30 km/h (19 mph))
|
Active
0 ... 25 %
|
Concerned Terminals: 33 (XC99)
|
|
|
T034
|
Tester Display Full Load Enrichment
|
- Ignition ON
- Engine OFF
- All consumers turned off
Note:
This data list parameter is in the data list 1 .
|
Inactive
|
- Engine running at idle speed, operating temperature
- Accelerator pedal briefly actuated to full load stop
|
Active
Value changing briefly
|
Concerned Terminals: -
|
|
|
T035
|
Tester Display Fan Control 1
|
Vehicle with air conditioning system:
- Air conditioning system OFF
- Coolant temperature is less than 95 °C (203 °F)
Note:
This data list parameter is in the data list 1 .
|
Inactive
|
- Coolant temperature is greater than 99 °C (210 °F)
or
- Air conditioning system ON
|
Active
|
Concerned Terminals: 14, 45, 46 (XC98)
|
|
|
T036
|
Tester Display Fan Control 2
|
Vehicle with air conditioning system:
- Air conditioning system OFF
- Coolant temperature is less than 98 °C (208 °F)
Note:
This data list parameter is in the data list 1 .
|
Inactive
|
- Coolant temperature is greater than 102 °C (216 °F)
or
- Air conditioning system ON
|
Active
|
Concerned Terminals: 14, 45, 46 (XC98)
|
|
|
T037
|
Tester Display Fan Control 3
|
Vehicle with air conditioning system:
- Air conditioning system OFF
- Coolant temperature is less than 101 °C (214 °F)
Note:
This data list parameter is in the data list 1 .
|
Inactive
|
- Coolant temperature is greater than 105 °C (221 °F)
or
- Air conditioning system ON
|
Active
|
Concerned Terminals: 14, 45, 46 (XC98)
|
|
|
T038
|
Tester Display Knock Control
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 2 .
|
Inactive
|
- Vehicle rapidly accelerated (up to approximately 30 km/h (19 mph))
|
Active
Value changing briefly
|
Concerned Terminals: 20, 52 (XC99)
|
|
|
T039
|
Tester Display Knock Retard Cylinder 1
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 2 .
|
0 °CA
|
- Vehicle rapidly accelerated (up to approximately 30 km/h (19 mph))
|
greater than 0 °CA
Value changing briefly
|
Concerned Terminals: 20, 52 (XC99)
|
|
|
T040
|
Tester Display Knock Retard Cylinder 2
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 2 .
|
0 °CA
|
- Vehicle rapidly accelerated (up to approximately 30 km/h (19 mph))
|
greater than 0 °CA
|
Concerned Terminals: 20, 52 (XC99)
|
|
|
T041
|
Tester Display Knock Retard Cylinder 3
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 2 .
|
0 °CA
|
- Vehicle rapidly accelerated (up to approximately 30 km/h (19 mph))
|
greater than 0 °CA
Value changing briefly
|
Concerned Terminals: 20, 52 (XC99)
|
|
|
T042
|
Tester Display Knock Retard Cylinder 4
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 2 .
|
0 °CA
|
- Vehicle rapidly accelerated (up to approximately 30 km/h (19 mph))
|
greater than 0 °CA
Value changing briefly
|
Concerned Terminals: 20, 52 (XC99)
|
|
|
T043
|
Tester Display B1S1 O2 Sensor Heater (Bank 1 Sensor 1)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 2 .
|
Active
Value changing briefly
|
Concerned Terminals: 49 (XC99)
|
|
|
T044
|
Tester Display B1S2 O2 Sensor Heater (Bank 1 Sensor 2)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 2 .
|
Active
Value changing briefly
|
Concerned Terminals: 35 (XC99)
|
|
|
T045
|
Tester Display B1S1 O2 Sensor (Bank 1 Sensor 1)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 2 .
|
50 ... 950 mV
Sensor signal alternates between high and low voltage range
|
Concerned Terminals: 8, 25 (XC99)
|
|
|
T046
|
Tester Display B1S2 O2 Sensor (Bank 1 Sensor 2)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 2 .
|
50 ... 950 mV
|
Concerned Terminals: 41, 57 (XC99)
|
|
|
T047
|
Tester Display B1 O2 Sensor Loop (Bank 1)
|
- Engine running at idle speed, cold
- All consumers turned off
Note:
This data list parameter is in the data list 2 .
|
Open
|
- Engine running at idle speed, operating temperature
- Accelerator pedal not actuated
|
Closed
|
- Accelerator pedal briefly actuated to full load stop
Note:
Even if the instructions given in the checking procedure are followed closely, the diagnostic tester may not indicate a signal change.
|
Open
|
Concerned Terminals: 8, 25 (XC99)
|
|
|
T048
|
Tester Display B1S1 Air/Fuel Ratio (Bank 1 Sensor 1)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 2 .
|
LEAN and RICH
Value changing briefly
|
Concerned Terminals: 8, 25 (XC99)
|
|
|
T049
|
Tester Display B1S2 Air/Fuel Ratio (Bank 1 Sensor 2)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 2 .
|
LEAN and RICH
|
Concerned Terminals: 41, 57 (XC99)
|
|
|
T050
|
Tester Display B1 Short Term Fuel Trim (Bank 1)
|
- Engine running at idle speed, operating temperature
- All consumers turned off
- Accelerator pedal not actuated
Note:
This data list parameter is in the data list 2 .
|
-5 ... 5 %
|
Concerned Terminals: 8, 25 (XC99)
|
|
|