Test
|
Work Order Description
|
Nominal Value
|
T001
|
Check: Component
|
- Ignition OFF
- Disconnect wiring harness connector from:
Y56 Solenoid Valve - Exhaust Gas Recirculation
- Ignition ON
-
Trouble Code Update
|
Is the diagnostic trouble code P1635 with status PRESENT stored?
|
|
T002
|
Check: Component
|
- Ignition OFF
- Disconnect wiring harness connector from:
A111 Throttle Valve - Positioner
- Ignition ON
-
Trouble Code Update
|
Is the diagnostic trouble code P1635 with status PRESENT stored?
|
|
T003
|
Check: Component
|
- Ignition OFF
- Disconnect wiring harness connector from:
B22 Sensor - Pedal Position
- Ignition ON
-
Trouble Code Update
|
Is the diagnostic trouble code P1635 with status PRESENT stored?
|
|
T004
|
Check: Component
|
- Ignition OFF
- Disconnect wiring harness connector from:
B28 Sensor - Camshaft
- Ignition ON
-
Trouble Code Update
|
Is the diagnostic trouble code P1635 with status PRESENT stored?
|
|
T005
|
Check: Short to Voltage of Voltage Supply Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
A84 Control Unit - Engine (Wiring Harness Connector XC9, XC10 )
- Ignition ON
- Measure voltage between the following terminals:
A84 Control Unit - Engine Wiring harness connector (wiring harness side) terminal 62 (XC9) & Ground
|
less than 0.3 V
|
|
|
T006
|
Check: Short to Voltage of Voltage Supply Circuit
|
- Measure voltage between the following terminals:
A84 Control Unit - Engine Wiring harness connector (wiring harness side) terminal 30 (XC9) & Ground
|
less than 0.3 V
|
|
|
T007
|
Check: Short to Ground of Voltage Supply Circuit
|
- Ignition OFF
- Measure resistance between the following terminals:
A84 Control Unit - Engine Wiring harness connector (wiring harness side) terminal 30 (XC9) & Ground
|
greater than 500 kOhm
|
|
|
T008
|
Check: Short to Voltage of Voltage Supply Circuit
|
- Ignition ON
- Measure voltage between the following terminals:
A84 Control Unit - Engine Wiring harness connector (wiring harness side) terminal 29 (XC9) & Ground
|
less than 0.3 V
|
|
|
T009
|
Check: Short to Voltage of Voltage Supply Circuit
|
- Measure voltage between the following terminals:
A84 Control Unit - Engine Wiring harness connector (wiring harness side) terminal 14 (XC9) & Ground
|
less than 0.3 V
|
|
|
T010
|
Check: Short to Ground of Voltage Supply Circuit
|
- Ignition OFF
- Measure resistance between the following terminals:
A84 Control Unit - Engine Wiring harness connector (wiring harness side) terminal 14 (XC9) & Ground
|
greater than 500 kOhm
|
|
|
T011
|
Check: Short to Voltage of Voltage Supply Circuit
|
- Ignition ON
- Measure voltage between the following terminals:
A84 Control Unit - Engine Wiring harness connector (wiring harness side) terminal 50 (XC10) & Ground
|
less than 0.3 V
|
|
|
T012
|
Check: Short to Voltage of Voltage Supply Circuit
|
- Measure voltage between the following terminals:
A84 Control Unit - Engine Wiring harness connector (wiring harness side) terminal 35 (XC10) & Ground
|
less than 0.3 V
|
|
|
T013
|
Check: Short to Ground of Voltage Supply Circuit
|
- Ignition OFF
- Measure resistance between the following terminals:
A84 Control Unit - Engine Wiring harness connector (wiring harness side) terminal 35 (XC10) & Ground
|
greater than 500 kOhm
|
|
|
T014
|
Check: Short to Ground of Signal Circuit
|
- Disconnect wiring harness connector from:
X125 Underhood Electronic Module
- Measure resistance between the following terminals:
X125 Underhood Electronic Module Wiring harness connector (wiring harness side) terminal 4 (XE2) & Ground
|
greater than 500 kOhm
|
|
|
T015
|
Check: Short to Voltage of Voltage Supply Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
X125 Underhood Electronic Module
- Ignition ON
- Measure voltage between the following terminals:
X125 Underhood Electronic Module Wiring harness connector (wiring harness side) terminal 4 (XE2) & Ground
|
less than 0.3 V
|
|
|
T016
|
Check: Short to Voltage of Voltage Supply Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
X125 Underhood Electronic Module Ignition ON
- Measure voltage between the following terminals:
X125 Underhood Electronic Module Wiring harness connector (wiring harness side) terminal 5 (EX2) & Ground
|
less than 0.3 V
|
|
|
T017
|
Check: Short to Voltage of Voltage Supply Circuit
|
- Ignition OFF
- Disconnect wiring harness connector from:
B39B Sensor - Temperature, Coolant
- Ignition ON
- Measure voltage between the following terminals:
A84 Control Unit - Engine Wiring harness connector (wiring harness side) terminal 62 (XC9) & Ground
- Disconnect each of the following components/control units consecutively from the wiring harness and repeat the measurement each time:
B65 Sensor - Knock Control
|
less than 0.3 V
|
|
|