vauxhall Workshop Repair Guides

Vauxhall Workshop Service and Repair Manuals

ABOUT US
C-006 Intake Camshaft Phasing Solenoid Valve Circuit > < C-004 Intake Camshaft Position Sensor Circuit

Astra H

C-005 - Exhaust Camshaft Position Sensor Circuit

Test

Work Order Description

Nominal Value
T001

Check: Interruption of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    B28E Sensor - Camshaft, exhaust
  • Ignition ON
  • Measure voltage between the following terminals:
    B28E Sensor - Camshaft, exhaust
    Wiring harness connector (wiring harness side) terminal 3
    &
    Ground

4.8 ... 5.2 V
Voltage Measurement Current Value: V
Yes: No:
T002

Check: Short to Voltage/Ground/Interruption of Signal Circuit
  • Measure voltage between the following terminals:
    B28E Sensor - Camshaft, exhaust
    Wiring harness connector (wiring harness side) terminal 1
    &
    Ground

4.8 ... 5.2 V
Voltage Measurement Current Value: V
Yes: No:
T003

Check: Short to Voltage of Ground Circuit
  • Measure voltage between the following terminals:
    B28E Sensor - Camshaft, exhaust
    Wiring harness connector (wiring harness side) terminal 2
    &
    Ground

less than 0.3 V
Voltage Measurement Current Value: V
Yes: No:
T004

Check: Short to Ground of Voltage Supply Circuit
  • Ignition OFF
  • Disconnect wiring harness connector from:
    A84 Control Unit - Engine
    (Wiring Harness Connector XC101 )
  • Measure resistance between the following terminals:
    B28E Sensor - Camshaft, exhaust
    Wiring harness connector (wiring harness side) terminal 2
    &
    Ground

greater than 500 kOhm
Resistance Measurement Current Value: kOhm
Yes: No:
T005

Check: Circuit Interruption of Ground Circuit
  • Measure resistance between the following terminals:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 26 (XC101)
    &
    B28E Sensor - Camshaft, exhaust
    Wiring harness connector (wiring harness side) terminal 2

less than 5 Ohm
Resistance Measurement Current Value: Ohm
Yes: No:
T006

Check: Short to Voltage/Ground/Interruption of Signal Circuit
  • Measure voltage between the following terminals:
    B28E Sensor - Camshaft, exhaust
    Wiring harness connector (wiring harness side) terminal 1
    &
    Ground

greater than 5.2 V
Voltage Measurement Current Value: V
Yes: No:


Result

Cause Of Fault
E001 Result: Defective Component
  • Defective component:
    B28E Sensor - Camshaft, exhaust
    or
    A84 Control Unit - Engine

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.

Note:

The replacement of the components must be done in the listed order.

The system must be checked for proper operation after every replacement.
E002 Result: Interruption
  • Circuit interruption between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 26 (XC101)
    &
    B28E Sensor - Camshaft, exhaust
    Wiring harness connector (wiring harness side) terminal 2
E003 Result: Short to Ground
  • Short circuit to ground between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 26 (XC101)
    &
    B28E Sensor - Camshaft, exhaust
    Wiring harness connector (wiring harness side) terminal 2
E004 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 26 (XC101)
    &
    B28E Sensor - Camshaft, exhaust
    Wiring harness connector (wiring harness side) terminal 2

or

  • Defective component:
    A84 Control Unit - Engine

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E005 Result: Short to Voltage
  • Short circuit to voltage between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 21 (XC101)
    &
    B28E Sensor - Camshaft, exhaust
    Wiring harness connector (wiring harness side) terminal 1

or

  • Defective component:
    A84 Control Unit - Engine

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E006 Result: Short to Ground/Interruption
  • Short circuit to ground/interruption of circuit between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 21 (XC101)
    &
    B28E Sensor - Camshaft, exhaust
    Wiring harness connector (wiring harness side) terminal 1

or

  • Defective component:
    A84 Control Unit - Engine

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E007 Result: Interruption
  • Circuit interruption between:
    A84 Control Unit - Engine
    Wiring harness connector (wiring harness side) terminal 42 (XC101)
    &
    B28E Sensor - Camshaft, exhaust
    Wiring harness connector (wiring harness side) terminal 3





C-006 Intake Camshaft Phasing Solenoid Valve Circuit > < C-004 Intake Camshaft Position Sensor Circuit