Special Service Tools
KM-301
|
Measuring Bridge
|
|
To measure piston projection
|
|
|
KM-313
|
Slide Hammer
|
|
To remove axle shafts in conjunction with KM-902
|
|
|
KM-412-A
|
Engine Overhaul Stand
|
|
To hold removed engine
|
|
|
KM-412-32
|
Engine adapter
|
|
Engine mount in conjunction with KM-412-A
|
|
|
KM-468-B
|
Holding Wrench
|
|
To wheel hub counterhold
|
|
|
KM-470-B
|
Angular Torque Wrench
|
|
Tightening screwed joints with tightening angle
|
|
|
KM-471
|
Adapter
|
|
To check pressurised cooling system in conjunction with cooling
system tester
|
|
|
KM-498-B
|
Oil pressure gauge
|
|
To check engine oil pressure in conjunction with KM-232
|
|
|
KM-507-C
|
Remover
|
|
To press tie rod joint out of steering knuckle
|
|
|
MKM-596-A
|
Temperature measuring instrument
|
|
|
|
|
MKM-604-D
|
Torx Bit and Socket Set
|
|
To remove and install Torx bolts/nuts
|
|
|
MKM-610
|
Torque Wrench, 1/2"
|
|
Range 30 – 130 Nm / 22 – 96 lbf. ft.
|
|
|
MKM-611
|
Torque Wrench, 3/8"
|
|
Range 10 – 60 Nm / 7 – 44 lbf. ft.
|
|
|
KM-662-C
|
Holding Wrench
|
|
Counterholding the belt pulley/crankshaft
|
|
|
MKM-669
|
Torque Wrench, 1/2"
|
|
Range: 50 – 300 Nm
|
|
|
KM-796-A
|
Remover
|
|
To open fuel system quick-release fittings
|
|
|
KM-902
|
Remover
|
|
To remove axle shafts in conjunction with KM-313
|
|
|
KM-904
|
Base Frame
|
|
To remove and install engine and transmission with KM-6312
|
|
|
KM-955
|
Locking Pins
|
|
To lock ribbed V-belt and chain tensioner
|
|
|
KM-956
|
Holding Wrench
|
Of which KM-956-1
|
Counterholding the belt pulley/crankshaft
|
|
|
KM-2358
|
Wire Cable
|
|
To suspend engine
|
|
|
KM-6130
|
Locating Pin
|
|
To fasten Ribbed V-belt tensioner
|
|
|
KM-6168-A
|
Centring Tool
|
|
To remove and install front axle in conjunction with KM-904
|
|
|
KM-6372
|
Counterholding aid
|
|
For counterholding alternator drive disc when
installing/removing
|
|
|
KM-6181
|
Fixing, steering play
|
|
Steering intermediate shaft adjustment
|
|
|
KM-6182-1
|
Pliers, straight
|
|
Removal/installation of compact clamps
|
|
|
KM-6182-2
|
Pliers, curved
|
|
Removal/installation of compact clamps
|
|
|
KM-6182-3
|
Pliers, flexible shaft
|
|
Removal/installation of compact clamps
|
|
|
KM-6347
|
Bracket
|
|
Holding the camshaft sprockets to release them
|
|
Tightening the fastening bolts in conjunction with KM-956-1
|
|
|
KM-6394
|
Engine/Transmission Mount
|
|
Aligning engine/transmission to front axle body
|
|
|
MKM-J-37228
|
Separation Tool
|
|
To disconnect oil pan
|
|
|
EN-46775
|
Centring cover, drive side, during installation
|
|
|
EN-46781
|
To lock camshaft
|
|
To check timing
|
|
|
EN-46782
|
Check compression
|
|
In conjunction with EN-46783
|
|
|
EN-46783
|
Adapter
|
|
For checking compression in conjunction with EN-46782
|
|
|
EN-46785
|
Rig pin
|
|
To check timing
|
|
|
EN-47655
|
Injector diagnostic tool
|
|
For checking injectors on Common Rail diesel engines (Bosch
injectors only)
|
|
|
EN-47656-1
|
Pressure test plugs - connecting piece
|
|
For checking charge air system for leaks in conjunction with
tyre inflator
|
|
|
EN-47656-2
|
Pressure test plugs
|
|
For checking charge air system for leaks in conjunction with
tyre inflator
|
|
|
EN-48391
|
Remover/Installer
|
|
For removing/installing glow plug, width 8 mm
|
|
|
|