Vauxhall Workshop Service and Repair Manuals

KM-113-2

Bracket

To hold rear differential in conjunction with KM-622-A

KM-160

Differential Housing Holding Wrench

To install and remove differential bevel gears in conjunction with KM-621-25 and KM-621-26 (no longer available)

KM-161-B

Bearing Puller

To remove pinion bearing from differential housing in conjunction with KM-621-18

KM-238-B

Height Gauge

Height adjustment of drive bevel gear in conjunction with KM-621-2

KM-252-2-B

Wire Cable

To determine slip value in conjunction with a weight of 455 N

KM-273

Bearing Press-on Piece

To press roller bearing onto differential housing

KM-302

Installer Sleeve

To press centre bearing onto propshaft

KM-305

Remover / Installer

To press bearing of inner drive pinion into and out of differential housing, also in conjunction with KM-621-11

KM-307-B

Remover Plate

To press constant velocity joint off drive shaft

KM-393

Installer

To install wheel journal flange retaining ring

KM-396

Ring Pliers

To remove and install retaining rings of drive shaft

KM-429-A

Measuring Device

To determine slip value with differential installed

KM-468-B

Holding Wrench

To counterhold rear wheel flange

KM-470-B

Angular Torque Wrench

To tighten various retaining parts in area of rear axle

KM-485

Car Jack Adapter

To hold rear differential (no longer available)

KM-500-A

Remover / Installer

To remove rear wheel bearing inner race in conjunction with KM-616

KM-501

Pressing-off tool

Pressing off the inner drive pinion bearing

KM-503-A

Remover

To press drive shaft flanges out of rear differential

KM-507-C

Remover

MKM-536-A

Torsiometer

To check slip torque

KM-547

Remover / Installer

To press on centre bearing of propshaft (no longer available)

KM-557-A

Puller Set

To remove damping bushing from crossmember

MKM-571-B

Dial Gauge

MKM-572

Measuring Device

To measure lateral runout of wheel journal flange

KM-616

Adapter

To remove rear wheel bearing inner ring in conjunction with KM-500-A

KM-617

Remover

To press drive shafts out of differential

KM-618-A

Installer

To install damping bushing of rear axle body

Modify Special Service Tool KM-618-2 to changed shape of Omega-B rear axle body by welding on approx. 14-mm high supports

KM-619

Remover / Installer

To press damping bushing out of and into semi-trailing arm

KM-620-B

Remover / Installer

To remove and install rear wheel hub and rear wheel bearing

KM-621-A

Mounting Tools

To overhaul rear differential

KM-622-A

Transmission Holder

To hold differential in conjunction with KM-113-2

To increase distance of KM-622 to differential reinforcement rib by welding on washers approx. 5 mm thick. After modifying, change tool number by adding "-A" to make KM-622-A

KM-623

Holding Wrench

To hold flange on differential when loosening and tightening fastening nut

KM-625

Installer

To press tapered roller bearing onto drive pinion

KM-628-A

Extractor Tool

To remove flange from differential

KM-629-A

Installer

To install seal ring on flange of differential

KM-671

Remover / Installer

To remove and install rear axle damping bushings

KM-833

Remover / Installer

To remove and install rear axle damping bushings

KM-885

Adapter

Measure differential slip torque, in conjunction with MKM-536-A.

KM-J-22610

Pliers

To tension bellows retaining straps on drive shaft

KM-6118

Remover

Pressing off the inner drive pinion bearing

KM-6194

Support plates

To raise vehicle with lifting platform when removing/installing rear axle

KM-6195

Transmission Holder

To hold transmission, in conjunction with KM-904 and hydraulic jack

KM-6393

Pressing-off tool

Pressing off the inner drive pinion bearing