Special Service Tools (X 18 XE, X 20 XEV, C 20 SEL, C 22 SEL)
KM-135 |
Adapter |
To measure engine oil pressure in conjunction with KM-498-B |
KM-194-E |
Spark Plug Wrench |
To remove/install spark plug |
KM-301 |
Gauge Bar |
To check piston projection |
KM-340-F |
Cutter Set |
To cut and correct valve seating |
KM-348 |
Valve Spring Compressor |
To compress valve spring in conjunction with KM-653-A |
KM-412 |
Engine Overhaul Stand |
To hold removed engine |
|
|
KM-412-8-A |
Adapter |
To hold engine in conjunction with KM-412 |
KM-422 |
Installer |
To press seal ring in camshaft |
KM-470-B |
Angular Torque Wrench |
To tighten cylinder head bolts |
KM-471 |
Adapter |
To check pressurised cooling system in conjunction with coolant tester |
KM-498-B |
Oil Pressure Gauge |
To check engine oil pressure in conjunction with KM-135 |
KM-535 |
Installer |
To install crankshaft seal ring in conjunction with KM-635 |
|
|
MKM-571-B |
Dial Gauge |
To check various components |
MKM-596-A |
Temperature Gauge |
To measure oil temperature |
MKM-604-D |
Torx Bit and Socket Set |
To remove/install Torx bolts |
KM-609 |
Electronic-Kit I |
To diagnose electrical and electronic systems |
MKM-610 |
Torque Wrench, 1/2" |
Measuring range 30 - 130 Nm / 22 - 96 lbf. ft. |
MKM-611 |
Torque Wrench, 3/8" |
Measuring range 10 - 60 Nm / 7 - 44 lbf. ft. |
|
|
KM-635 |
Installer |
To install rear crankshaft seal ring in conjunction with KM-535 |
KM-652 |
Flywheel / Drive Disc Holder |
To lock flywheel or drive disc |
KM-653-A |
Adapter |
To tension valve spring in conjunction with KM-348 |
KM-662-C |
Holding Wrench |
To hold toothed belt drive gear when removing and installing fastening bolt |
MKM-667 |
Pressure and Vacuum Pump |
To check vacuum units for leaks |
KM-693-A |
Installer |
To install front crankshaft seal ring |
|
|
KM-726-A |
Oil Filter Wrench |
To remove/install the oil filter |
KM-796 |
Dismantler |
To open quick-release fittings for fuel system |
KM-798 |
Dial Gauge |
Measure backlash |
KM-805 |
Reamer 6 mm |
To ream the valve guide, oversize 0.075 mm |
KM-835-A |
Installer (6 mm) |
To install the valve stem seal |
KM-836 |
Remover |
To remove spark plug connector |
|
|
KM-840 |
Remover |
To remove valve stem seals |
KM-845 |
Suction Device |
To remove the hydraulic valve lifters |
KM-853 |
Locking Tool |
To lock the camshaft sprockets |
MKM-883-1 |
Engine Bridge |
To hold/lift the engine |
MKM-883-2 |
Adapter Plate |
To align engine in conjunction with MKM-883-1 |
MKM-889 |
Remover/Installer |
To remove/install the valve stem seals (cylinder head installed) |
|
|
KM-897 |
Third Engine Transportation Shackle |
To remove and install engine |
KM-904 |
Base Frame |
To remove and install various vehicle components with additional adapters |
KM-905 |
Centring Locator |
To remove/install the front axle body in conjunction with KM-904 |
KM-913-A |
Installation Wrench |
To tension/relax the ribbed V-belt tension roller |
KM-949 |
Measuring Gauge |
Measure backlash |
KM-2355 |
Socket Wrench |
To loosen/tighten cylinder head bolts |
|
|
KM-J-34730-91 |
Pressure Tester |
To check fuel pressure |
|
|
|