|
Replace carpet - complete (without adjustable rear
seats) - L35
 Remove
| 2. |
Wait 1 minute for airbag to deactivate
|
| 3. |
Detach belt securing panel - driver's side
| • |
Unclip panel upwards (1)
|
|
| 4. |
Detach belt securing panel - passenger side
| • |
Unclip panel upwards (1)
|
|
| 5. |
Attach seat belt at front seat - driver's side
|
| 6. |
Attach seat belt at front seat - passenger's side
|
|
|
| 7. |
Detach driver's side front seat
|
| 8. |
Detach passenger side front seat
|
| 9. |
Remove driver's side front seat
| • |
Remove from front guide
|
| • |
Release and disconnect compact connector
|
|
| 10. |
Remove passenger's side front seat
| • |
Remove from front guide
|
| • |
Release and disconnect compact connector
|
|
|
|
| 11. |
Detach footwell instrument panel padding left and right
| • |
Unscrew 2x screws on driver's side and remove footwell
panelling from bracket
|
| • |
Unscrew 2x screws on passenger's side and remove footwell
panelling from bracket
|
|
|
|
| 12. |
Detach central console
|
| 13. |
Remove rear seat cushion
| • |
Open the lock at the loop
|
|
| 14. |
Remove rear seat backrest - right side
| • |
Unscrew 3x bolts at the front
|
| • |
Fold down rear seat backrest
|
| • |
Unscrew 3x bolts at the back
|
|
| 15. |
Remove rear seat backrest
|
|
|
| 16. |
Remove sill strip completely - both sides
| • |
Remove inner panelling sill upwards
|
|
|
|
| 17. |
Detach lower C-pillar panel, both sides
| • |
Unclip 4x clips
| – |
Pull out panelling in lower area of the B-pillar cover
|
|
|
|
|
| 18. |
Remove yaw sensor (2)
| • |
Unscrew 2x nuts (arrows)
|
| • |
Disconnect wiring harness plug (1)
|
|
| 19. |
Remove yaw sensor retaining plate
|
|
|
|
| 20. |
Remove carpet - completely
| • |
Open quick release fastener
|
|
|
Install
| 21. |
Install carpet - completely
Note: 2nd mechanic
required!
| • |
Close quick release fastener
|
|
| 22. |
Install yaw sensor retaining plate
|
| 23. |
Install yaw sensor
| • |
Connect wiring harness plug
|
|
| 24. |
Install lower C-pillar inner panelling - left side
| • |
Clip in 4x clips
| – |
Place panelling in lower area of the B-pillar cover
|
|
|
| 25. |
Install lower C-pillar inner panelling - right side
| • |
Clip in 4x clips
| – |
Place panelling in lower area of the B-pillar cover
|
|
|
| 26. |
Insert rear seat backrest
|
| 27. |
Install rear seat backrest
| • |
Fold down rear seat backrest
|
| • |
Tighten 3x bolts, front
Note: Use screw locking
compound
|
|
| 28. |
Insert rear seat cushions and lock
|
| 29. |
Install centre console
|
| 30. |
Attach footwell instrument panel padding left and right
| • |
Tighten 2x bolts driver's side
|
| • |
Tighten 2x bolts passenger's side
|
|
| 31. |
Install sill strip completely - both sides
|
| 32. |
Insert driver's side front seat
| • |
Connect and latch compact connector
|
| • |
Insert seat in front guide
|
|
| 33. |
Fasten driver's side front seat
| • |
Tighten 2x bolt 35 Nm
Note: Use screw locking
compound
|
|
| 34. |
Attach seat belt driver's side
| • |
Tighten bolt 20 Nm
Note: Use screw locking
compound
|
|
| 35. |
Insert driver's side front seat panel
| • |
Place front seat in original position
|
|
| 36. |
Insert front seat - passenger side
| • |
Connect and latch compact connector
|
| • |
Insert seat in front guide
|
|
| 37. |
Fasten passenger side - front seat
| • |
Tighten 2x bolt 35 Nm
Note: Use screw locking
compound
|
|
| 38. |
Attach seat belt on passenger's side
| • |
Tighten bolt 20 Nm
Note: Use screw locking
compound
|
|
| 39. |
Insert passenger's side front seat panel
| • |
Place front seat in original position
|
|
| 40. |
Install rear bench seat
| • |
Insert rear seat cushion and position
|
|
| 42. |
Program volatile memories
|
|
