Emgine oil intake duct - r r

Operation 1084B26 · ENGINE OIL LUBRICATION CIRCUIT

Removing

- 7055B54 under-engine guard - r r

- 2110A60 manual gearbox/engine coupling bracket - r+r

- 1020A30 engine oil drain plug - replace

- 1020A20 crank case oil sump - r + r clean seals for sealant application

- 1084B28 engine oil intake pump - r + r with crankcase sump removed

Removing

Position the car on the ramp.

Make sure that the ignition key is in the OFF position; then disconnect the battery negative terminal.

Drain the air conditioner coolant circuit - 0010T84 coolant for air conditioning system dehydrate and recharge.

Carry out - 7055B54 under-engine guard - r r.

Carry out - 4450B04 right front wheel r r.

Carry out.

Carry out - 1092C10 power steering and/or self-levelling suspension pump drive belt - r + r.

Carry out - 1092G10 single engine belt r r.

Carry out - 1092A10 Crankshaft services PULLEY - R.R..

Carry out - 2110A60 manual gearbox/engine coupling bracket - r+r.

Carry out - 1020A20 crank case oil sump - r + r clean seals for sealant application.

Carry out - 1020B10 cover of timing system with chain drive - r + r replace oil seal and gasket.

1. At the bench, undo the bolts (1a) and separate the engine oil inlet duct (1b) complete with gasket (1c) from the timing cover.

Removing

- 7055B54 under-engine guard - r r

- 1076B50 exhaust pipe attachment to engine - r + r

- 1020A20 crank case oil sump - r + r clean seals for sealant application

- 1084B28 engine oil intake pump - r + r with crankcase sump removed

Removing

Proceed with the removal - 5530B10 battery - r+r.

Proceed with the removal - 5530B52 Battery DRIP TRAY/SUPPORT - R.R..

Proceed with the removal - 4450B12 front or rear wheels (two) - r+r.

Proceed with the removal - 1044B10 fuel filter assembly - r + r or replace.

Proceed with the removal - 7210E22 R.R. WINDSCREEN BASE TRIM.

Proceed with the removal - 7055B54 under-engine guard - r r.

Proceed with the removal - 7210E10 R.R. FRONT BUMPER.

Drain the air conditioning system - 5040A10 Air conditioning refrigerant CIRCUIT - Draining and Refilling.

Proceed with the removal - 4130B10 power steering fluid resevoir r r.

Proceed with the removal - 1088B10 engine cooling tank - r + r.

Proceed with the removal - 1004B10 power unit with manual gearbox - r + r.

Proceed with the removal - 1004D10 power unit (manual gearbox), removed, remove and re-build.

Proceed with the removal - 1020A20 crank case oil sump - r + r clean seals for sealant application.

Proceed with the removal - 1084B28 engine oil intake pump - r + r with crankcase sump removed.

Refitting

- 1084B28 engine oil intake pump - r + r with crankcase sump removed

- 1020A20 crank case oil sump - r + r clean seals for sealant application

- 1020A30 engine oil drain plug - replace

- 2110A60 manual gearbox/engine coupling bracket - r+r

- 0010T11 engine oil check level and top up

- 7055B54 under-engine guard - r r

Refitting

Place the engine oil inlet duct, complete with gasket, back in its housing on the timing cover and secure it using the bolts.

Carry out - 1020B10 cover of timing system with chain drive - r + r replace oil seal and gasket.

Carry out - 1020A20 crank case oil sump - r + r clean seals for sealant application.

Carry out - 2110A60 manual gearbox/engine coupling bracket - r+r.

Carry out - 1092A10 Crankshaft services PULLEY - R.R..

Carry out - 1092G10 single engine belt r r.

Carry out - 1092C10 power steering and/or self-levelling suspension pump drive belt - r + r.

Carry out.

Carry out - 4450B04 right front wheel r r.

Connect the battery negative terminal.

Refill the engine oil lubrication system - 0010T11 engine oil check level and top up.

Refill the engine cooling system with coolant - 0010T20 coolant change.

Fill the air conditioner coolant circuit - 0010T84 coolant for air conditioning system dehydrate and recharge.

Carry out - 7055B54 under-engine guard - r r.

Remove the car from the ramps.

Refitting

- 1084B28 engine oil intake pump - r + r with crankcase sump removed

- 1020A20 crank case oil sump - r + r clean seals for sealant application

- 1076B50 exhaust pipe attachment to engine - r + r

- 7055B54 under-engine guard - r r

- 0010T11 engine oil check level and top up

Refitting

Proceed with the refitting - 1084B28 engine oil intake pump - r + r with crankcase sump removed.

Proceed with the refitting - 1020A20 crank case oil sump - r + r clean seals for sealant application.

Proceed with the refitting - 1004D10 power unit (manual gearbox), removed, remove and re-build.

Proceed with the refitting - 1004B10 power unit with manual gearbox - r + r.

Proceed with the refitting - 1088B10 engine cooling tank - r + r.

Proceed with the refitting - 4130B10 power steering fluid resevoir r r.

Drain the air conditioning system - 5040A10 Air conditioning refrigerant CIRCUIT - Draining and Refilling.

Proceed with the refitting - 7210E10 R.R. FRONT BUMPER.

Proceed with the refitting - 7055B54 under-engine guard - r r.

Proceed with the refitting - 7210E22 R.R. WINDSCREEN BASE TRIM.

Proceed with the refitting - 1044B10 fuel filter assembly - r + r or replace.

Proceed with the refitting - 4450B12 front or rear wheels (two) - r+r.

Proceed with the refitting - 5530B52 Battery DRIP TRAY/SUPPORT - R.R..

Proceed with the refitting - 5530B10 battery - r+r.

Refill the engine cooling system with coolant - 0010T20 coolant change.