Workshop Manuals Factory service & repair Fiat
01 00 General information and technical data02 10 Engine03 18 Clutch04 21 Gearbox and differential05 27 Axle06 33 Braking system07 41 Steering08 44 Suspension and wheels09 50 Auxiliary units10 55 Electrical equipment11 70 Bodywork12 Diagnosis13 Tests14 Wiring diagrams
Fiat Seicento Factory Service Manual (1998-2010)02 · 10 Engine
02 · Engine

Refitting

Make
Fiat
Model
Seicento Factory Service Manual
Year
1998–2010
Section
Fuel tank and pipes (1108) › Refitting
10 EngineRefitting

(Op. 1040A20 continued)

  1. Lower the jack and remove the fuel tank complete with fuel delivery hose and valve with pipes and electric pump.
Line drawing of a fuel tank assembly showing the fuel pump access cover, electrical connector, and various hoses and pipes attached to the unit. A callout line points to the bottom left corner labeled '1'.

Refitting

  • Using a hydraulic jack, install the fuel tank complete with fuel delivery hose and valves with pipes and electric pump.
  • Insert the over-flow pipe.
  • Tighten the screw and the nut securing the front bracket of the fuel tank to the body to correct torque
FasteningComponentØValue (daNm)
ScrewFUEL TANK BRACKETM85.0
FasteningComponentØValue (daNm)
NutFUEL TANK BRACKETM85.0
  • Tighten the screws securing the fuel tank to the body to correct torque
FasteningComponentØValue (daNm)
ScrewFUEL TANKM85.0
  • Remove the hydraulic jack.
  • Connect the fuel inlet hose to the fuel tank.
  • Install the right-hand end of the hand brake cable on the rear right-hand handbrake drum control.
  • Reposition the fuel filter.
  • Tighten the screws securing the fuel filter to the bracket on the tank.
  • Connect the active charcoal filter hose to the fuel vapour recovery reservoir.
  • Connect the hoses of the fuel tank valves to the fuel vapour recovery reservoir.
  • Connect the fuel delivery hose from the tank to the filter.
  • Complete with Op. 1076B20 Rear exhaust SILENCER - R.R.
  • Lower the vehicle.
  • Complete with Op. 4450B11 Rear WHEEL (one) - R.R.
  • Insert the fuel return hose.
  • Connect the electrical connection to the electric fuel pump and level gauge
NameConnector
Electric fuel pump and level gaugeN40
  • Install the fuel pump access cover and secure it with the screws.
  • Complete with Op. 7050A22 Rear seat CUSHION - R.R.
  • Connect the (-) negative terminal of the battery
NameConnector
BatteryA1
  • Remove the vehicle from the hoist.
  • Fill the fuel tank with the specified fuel.

1040A22 - FUEL TANK - R.R. FOR VERSION WITH EVAPORATION CONTROL SYSTEM FOR REPLACEMENT

Removal

  • Position the vehicle on a hoist.
  • Disconnect the negative (-) battery terminal.
NameConnector
BatteryA1
  • Suck up the fuel from the tank using a suitable tool.
  • Follow Op. 7050A22 CUSHION of rear seat - R.R.
  • Follow Op. 4450B11 Rear WHEEL (one) - R.R.
  • Raise the vehicle.
  • Follow Op. 1076B20 Rear exhaust SILENCER - R.R.
  • Follow Op. 1040A20 FUEL TANK - R.R. and fuel decanting for versions with evaporation control system
  • Disconnect the fuel delivery hose from the fuel pump.

(Cont.)

Parts & tools for this job For 1998 Fiat Seicento

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.