Workshop Manuals Factory service & repair

Lancia Thesis Factory Service Manual (2002-2009)14 · Suspension and wheels

14 · Steering & suspension

Rear suspension CAMBER ROD - R.R.

Make: Lancia
Model: Thesis Factory Service Manual
Year: 2002–2009
Section: Rear suspension › Rear suspension CAMBER ROD - R.R.

‹ Prev Rear suspension ANTI-ROLL BAR JOINT (one), left or right - R.R. on vehicle Next › Rear suspension CAMBER ROD - R.R. WITH SUSPENSION CROSSMEMBER REMOVED

Suspension and wheelsRear suspension CAMBER ROD - R.R.

Rear suspension CAMBER ROD - R.R.

Operation 4420C80 · ANTI-ROLL BAR/SUSPENSION RODS REAR

Removing

- Position the vehicle on a lift.

See in Op. 4450B13 Rear WHEELS (two) - R.R.

See in Op. 7055B45 Right rear wheel arch liner - R.R.

See in Op. 1076B20 Rear exhaust SILENCER - R.R.

See in Op. 4420D10 REAR SUSPENSION AXLE - R.R.

See in Op. 4420C82 Rear suspension CAMBER ROD - R.R. WITH SUSPENSION CROSSMEMBER REMOVED

Refitting

See in Op. 4420C82 Rear suspension CAMBER ROD - R.R. WITH SUSPENSION CROSSMEMBER REMOVED

See in Op. 4420D10 REAR SUSPENSION AXLE - R.R.

See in Op. 1076B20 Rear exhaust SILENCER - R.R.

See in Op. 7055B45 Right rear wheel arch liner - R.R.

See in Op. 4450B13 Rear WHEELS (two) - R.R.

- Place the vehicle in Standard "A" conditions, in other words with the vehicle mass complete, spare wheel, tool kit, all supplies and accessories (oil, engine coolant, etc.) and a full fuel tank.

- Check that the tyre inflation pressure is correct.

- Position the vehicle on a support so that the wheels are resting on the ground.

2.4 20V

- Check that after the vehicle has been placed in standard "A" conditions, the measurement "D"-"C" corresponds to the figure given in the table below.

	Subject	Value
	Rear wheel geometry	mm
	D - C	21 ± 5
	Standard A

Rear suspension CAMBER ROD - R.R.

2.4 JTD 10V

- Check that after the vehicle has been placed in standard "A" conditions, the measurement "D"-"C" corresponds to the figure given in the table below.

	Subject	Value
	Rear wheel geometry	mm
	D - C	21 ± 5
	Standard A

Rear suspension CAMBER ROD - R.R.

3.0 V6, 3.2 V6

- Check that after the vehicle has been placed in standard "A" conditions, the measurement "D"-"C" corresponds to the figure given in the table below.

	Subject	Value
	Rear wheel geometry	mm
	D - C	21 ± 5
	Standard A

Rear suspension CAMBER ROD - R.R.

2.0 TB

- Check that after the vehicle has been placed in standard "A" conditions, the measurement "D"-"C" corresponds to the figure given in the table below.

	Subject	Value
	Rear wheel geometry	mm
	D - C	21 ± 5
	Standard A

Rear suspension CAMBER ROD - R.R.

- Check that after the vehicle has been placed in standard "A" conditions, the measurement "D"-"C" corresponds to the figure given in the table below.

	Subject	Value
	Rear wheel geometry	mm
	D - C	21 ± 5
	Standard A

Rear suspension CAMBER ROD - R.R.

All versions

- Tighten the bolts fixing the rod to the steering knuckle to torque.

	Value - daNm	Fastening	Component	Ø
	(Steering knuckle) 11	Bolt	HOUSING LINK	M12X1.25

- Tighten the bolts fixing the camber rod to the rear axle to torque.

	Value - daNm	Fastening	Component	Ø
	(Crossmember side) 9	Nut	HOUSING LINK	M12X1.25

See in Op. 4450A40 REAR WHEEL GEOMETRY - Check using optical equipment - Includes rear wheel toe-in adjustment if necessary

‹ Prev Rear suspension ANTI-ROLL BAR JOINT (one), left or right - R.R. on vehicle Next › Rear suspension CAMBER ROD - R.R. WITH SUSPENSION CROSSMEMBER REMOVED

Parts & tools for this job For 2002 Lancia Thesis

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.