Outline: Specifications
- Make
- Mazda
- Model
- MX-5 (NA) Factory Workshop Manual
- Year
- 1990–1992
- Section
- Outline › Specifications
ClutchSpecifications
SPECIFICATIONS
| Item | Engine/Transmission Model | ||
|---|---|---|---|
| B6 DOHC | M5M-D | ||
| Clutch control | Hydraulic | ||
| Clutch cover | Type | Diaphragm spring | |
| Set load N (kg, lb) | 4,022 (410, 902) | ||
| Clutch disc | Outer diameter mm (in) | 200 (7.87) | |
| Inner diameter mm (in) | 130 (5.12) | ||
| Thickness | Pressure plate side mm (in) | 3.5 (0.14) | |
| Flywheel side mm (in) | 3.5 (0.14) | ||
| Clutch pedal | Type | Suspended | |
| Pedal ratio | 6.13 | ||
| Full stroke mm (in) | 120 (4.72) | ||
| Height mm (in) | 175—185 (6.89—7.28) | ||
| Master cylinder inner diameter mm (in) | 15.87 (0.625) | ||
| Release cylinder inner diameter mm (in) | 19.05 (0.750) | ||
| Clutch fluid | SAE J1703 or FMVSS116 DOT-3 | ||
TROUBLESHOOTING GUIDE
| Problem | Possible Cause | Action | Page |
|---|---|---|---|
| Slipping | Clutch disc facing worn excessively | Replace | H–14 |
| Clutch disc facing surface hardened or oil on surface | Repair or replace | H–14 | |
| Pressure plate damaged | Repair or replace | H–14 | |
| Diaphragm spring damaged or weak | Replace | H–14 | |
| Insufficient clutch pedal play | Adjust | H– 5 | |
| Clutch pedal sticking | Repair or replace | H– 6 | |
| Flywheel damaged | Repair or replace | H–14 | |
| Faulty disengagement | Excessive runout or damaged clutch disc | Replace | H–14 |
| Clutch disc splines rusted or worn | Remove rust or replace | H–14 | |
| Oil on facing | Repair or replace | — | |
| Diaphragm spring weak | Replace | H–14 | |
| Excessive clutch pedal play | Adjust | H– 5 | |
| Insufficient clutch fluid | Add fluid | H– 2 | |
| Leakage of clutch fluid | Locate and repair or replace | — | |
| Clutch vibrates when accelerating | Oil on facing | Repair or replace | H–14 |
| Torsion rubbers weak | Replace | H–14 | |
| Clutch disc facing hardened or damaged | Repair or replace | H–14 | |
| Clutch disc facing rivets loose | Replace | H–14 | |
| Pressure plate damaged or excessive runout | Replace | H–14 | |
| Flywheel surface hardened or damaged | Repair or replace | H–14 | |
| Loose or worn engine mount | Tighten or replace | — | |
| Clutch pedal sticking | Pedal shaft not properly lubricated | Lubricate or replace | H– 6 |
| Abnormal noise | Clutch release bearing damaged | Replace | H–14 |
| Poor lubrication of release bearing sleeve | Lubricate or replace | H–14 | |
| Torsion spring weak | Replace | H–14 | |
| Excessive crankshat end play | Repair | Refer to Section B | |
| Pilot bearing worn or damaged | Replace | H–14 | |
| Worn pivot points of release fork | Repair or replace | H–14 |
Parts & tools for this job For 1990 Mazda MX-5
- PARTClutch kitSearch: Mazda MX-5 1990 clutch kit
- TOOLClutch alignment toolSearch: clutch alignment tool
- FLUIDGear oilSearch: Mazda MX-5 manual gearbox oil
Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.