Troubleshooting guide
- Make
- Mazda
- Model
- MX-5 (NA) Factory Workshop Manual
- Year
- 1990–1992
- Section
- Troubleshooting guide › Troubleshooting guide
Braking systemTroubleshooting guide
| Problem | Possible cause | Action | Page |
|---|---|---|---|
| Poor braking | Leakage of brake fluid | Repair | — |
| Air in lines | Air bleed | P– 6 | |
| Worn pad | Replace | P–18,22 | |
| Brake fluid, grease, oil, or water on pad | Clean or replace | P–18,22 | |
| Hardening of pad surface or poor contact | Grind or replace | P–18,22 | |
| Malfunction of disc brake piston | Replace | P–19,23 | |
| Malfunction of master cylinder | Repair or replace | P–10 | |
| Malfunction of power brake unit | Repair or replace | P–15 | |
| Malfunction of check valve (vacuum hose) | Repair or replace | P–15 | |
| Damaged vacuum hose | Replace | P–15 | |
| Deterioration of flexible hose | Replace | P– 6 | |
| Malfunction of proportioning bypass valve (PBV) | Replace | P–16 | |
| Brakes pull to one side | Worn pad | Replace | P–18,22 |
| Brake fluid, grease, oil, or water on pad | Clean or replace | P–18,22 | |
| Hardening of pad surface or poor contact | Grind or replace | P–18,22 | |
| Abnormal wear, distortion, or eccentricity of disc | Repair or replace | Section M | |
| Malfunction of automatic adjuster in rear brake | Repair | — | |
| Looseness or deformation of dust cover mounting bolt | Tighten or replace | Section M | |
| Malfunction of disc brake piston | Repair or replace | P–19,23 | |
| Worn or improperly adjusted wheel bearing preload | Replace or adjust | Section M | |
| Improper adjustment of wheel alignment | Adjust | Section R | |
| Unequal tire air pressure | Adjust | Section Q | |
| Brakes do not release | No brake pedal play | Adjust | P– 8 |
| Improper adjustment of push rod clearance | Adjust | P–11 | |
| Clogged master cylinder return port | Clean | — | |
| Pad not returning properly | Repair | — | |
| Improper return of malfunction of brake caliper piston | Replace | P–21,25 | |
| Excessive runout of disc plate | Replace | Section M | |
| Improper adjustment of wheel bearing preload | Adjust or replace | Section M | |
| Pedal goes too far (Too much pedal stroke) |
Air in system because of insufficient brake fluid | Add fluid and bleed air | P– 6 |
| Improper adjustment of pedal play | Adjust | P– 8 | |
| Worn pad | Replace | P–18,22 | |
| Air in lines | Bleed air | P– 6 | |
| Abnormal noise or vibration during braking | Worn pad | Replace | P–18,22 |
| Deterioration of pads | Grind or replace | P–18,22 | |
| Brakes do not release | Repair | — | |
| Foreign material or scratches on disc plate contact surface | Clean | — | |
| Looseness of caliper mounting bolt(s) | Tighten | P–19,23 | |
| Damage or deviation of disc contact surface | Replace | Section M | |
| Poor contact of pads | Repair or replace | P–18,22 | |
| Insufficient grease on sliding parts | Apply grease | — |
Parts & tools for this job For 1990 Mazda MX-5
- TOOLTorque wrenchSearch: 3/8 inch torque wrench
- TOOLSocket setSearch: socket set metric
- BOOKHaynes manualSearch: Haynes manual Mazda MX-5
Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.