Wheel alignment
- Make
- Mazda
- Model
- MX-5 (NA) Factory Workshop Manual
- Year
- 1990–1992
- Section
- Wheel Alignment › Wheel alignment
WHEEL ALIGNMENT
PRE-INSPECTION
- Check the tire inflations, and adjust to the recommended pressure if necessary.
- Inspect the front wheel bearing paly and correct if necessary.
- Inspect the wheel and tire runouts.
- Inspect the ball joints and steering linkage for excessive looseness.
- The vehicle must be on level ground and carry no luggage or passengers.
- Measure the height from the center of the wheel to the fender brim. The difference between left and right must be not exceed 10mm (0.31 in), and the difference between front and rear must be 20mm ± 10mm (0.62 ± 0.31 in).
Caution
• The proper caster and camber angle vary depending on the vehicle height. Refer to the following and to page R–9 for the specifications.
• Inspection and adjustment of wheel alignment must be done with the vehicle unladed*1.
FRONT WHEEL ALIGNMENT
Specifications (Unladed*1)
| Item | Specifications | ||
|---|---|---|---|
| Total toe-in | mm (in) | 3 ± 3 (0.12 ± 0.12) | |
| degree | 0°18' ±18' | ||
| Maximum steering angle | Inner | 37°23' ± 2° | |
| Outer | 32°32' ± 2° | ||
| Kingpin angle | 11°20' | ||
| Camber angle | Height from center of wheel to fender brim mm (in) | 328—337 (12.9—13.3) | −0°20' ± 45'*2 |
| 338—347 (13.3—13.7) | 0°03' ± 45'*2 | ||
| 348—357 (13.7—14.1) | 0°24' ± 45'*2 | ||
| 358—367 (14.1—14.4) | 0°44' ± 45'*2 | ||
| 368—377 (14.4—14.8) | 1°02' ± 45'*2 | ||
| Caster angle | Height from center of wheel to fender brim mm (in) | 328—337 (12.9—13.3) | 5°16' ± 45' |
| 338—347 (13.3—13.7) | 5°02' ± 45' | ||
| 348—357 (13.7—14.1) | 4°49' ± 45' | ||
| 358—367 (14.1—14.4) | 4°35' ± 45' | ||
| 368—377 (14.4—14.8) | 4°21' ± 45' | ||
*1 Fuel tank full; radiator coolant and engine oil at specified levels; spare tire, jack, and tools in designated positions.
*2 Difference between left and right must not exceed 1°.
Adjustment
Maximum steering angle
- Remove the steering gear boot clamp.
- Loosen the tie-rod locknut.
- Turn the tie-rod to provide the correct maximum steering angle.
- After adjustment, tighten the locknut to the specified torque.
Tightening torque:
34—39 N·m (3.5—4.0 m·kg, 25—29 ft-lb)
- Adjust the toe-in. (Refer to page R–8.)
- Verify that the boot is not twisted, and install the boot clamp.
Parts & tools for this job For 1990 Mazda MX-5
- TOOLTie rod end toolSearch: tie rod end puller
- TOOLBall joint separatorSearch: ball joint separator
- FLUIDPower steering fluidSearch: Mazda power steering fluid
Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.