Workshop Manuals Factory service & repair SEAT
01 Power transmission02 Running gear03 Body04 Power tramsmission05 Power unit06 Vehicle electrics07 Heating-ventilation-air conditioning system08 Automatic gearbox09 Engine, mixture preparation10 Engine, mechanics11 Manual gearbox12 Running gear - self diagnosis13 Heating and air conditioning14 Bodywork15 Heating, ventilation, air conditioning system
SEAT Leon Mk201 · Power transmission
01 · Transmission

Gearbox cover: repairs

Make
SEAT
Model
Leon Mk2
Section
Gearbox mechanics,operation, construction,diff. › Gearbox cover › Gearbox cover: repairs
Power transmissionGearbox cover: repairs
Gearbox cover: repairs
Check the tool and equipment equivalence table according to the applicability between Seat / VW / Audi / Skoda → Chapter
   
Gearbox cover: repairs – SEAT Leon Mk2
Special tools and workshop equipment required
t  Clutch press -VW 401-, see equivalent → Anchor
t  Clutch press -VW 402-, see equivalent → Anchor
t  Compression column -VW 408 A-, see equivalent → Anchor
t  Die -VW 412-
t  Thrust pad -VW 512-
t  Tube element -VW 519-

   
Gearbox cover: repairs – SEAT Leon Mk2
t  Thrust pad -VW 447 i-
t  Retaining plate -VW 801-
t  Guide pin -10 - 15-
t  Aligning punch -3176-, see equivalent → Anchor
t  Torque wrench -V.A.G 1331-, see equivalent → Anchor.
t  -1-Interior extractor -Kukko 21/2-
t  -1-Interior extractor -Kukko 21/5-
t  -1-Interior extractor -Kukko 21/6-
t  -4-Support bracket -Kukko 22/2-

   
Pulling roller bearing for output shaft out of gearbox cover
A  - Counter-support, e.g. -Kukko 22/2-
B  - Internal puller 37...46 mm, e.g. -Kukko 21/6-
Gearbox cover: repairs – SEAT Leon Mk2  Note
Always renew roller bearing after pulling out.
  A34-10124
Pressing new roller bearing for output shaft into gearbox cover as far as the stop (press in carefully)
Support gearbox cover with thrust plate -VW 447 i- directly below bearing mounting.
  A35-10015
Pulling out ball sleeve -C- from gearbox cover
A  - Counter-support, e.g. -Kukko 22/2-
B  - Internal puller 14.5...18.5 mm, e.g. -Kukko 21/2-
  A34-10091
Driving ball sleeve into gearbox cover until flush
Fit ball sleeve -1- and -2- so that side with lettering (thicker metal) faces guide pin -10 - 15- or centring mandrel - 3176-.
Gearbox cover: repairs – SEAT Leon Mk2  Note
Due to the housing depth use centring mandrel -3176- for driving in ball sleeve -2-.
  A34-10092
Pulling roller bearing for input shaft out of gearbox cover
Shorten (cut off) oil guide in needle roller bearing in order to insert internal puller-B-.
A  - Counter-support, e.g. -Kukko 22/2-
B  - Internal puller 30...37 mm, e.g. -Kukko 21/5-
Gearbox cover: repairs – SEAT Leon Mk2  Note
Always renew roller bearing after pulling out.
  A35-10016
Pressing new roller bearing for input shaft into gearbox cover as far as the stop (press in carefully)
Support gearbox cover with thrust plate -VW 447 i- directly below bearing mounting.
  A35-10017
Securing needle roller bearing and needle bearing in gearbox cover.
–  Insert retaining plate -2- with the high shoulder -arrow- facing needle bearing -1- into gearbox cover.
–  Tighten hexagon socket head bolt -3- to 24 Nm.
  A34-10093

The same page in: Leon Mk1.

Parts & tools for this job For SEAT Leon

Links open Amazon search results in a new tab. As an Amazon Associate I earn from qualifying purchases.