skoda Workshop Repair Guides

Skoda Workshop Service and Repair Manuals

ABOUT US
Removing and installing lateral acceleration senderG200 and yaw rate senderG202 or ESP sensor unitG419 - vehicles with ABS/EDL/T > < Setting, removing and installing the brake light switchF

Fabia Mk1

Removing and installing steering angle senderG85 - vehicles with ABS/EDL/TCS/ESP BOSCH 5.7 or ABS/TCS/ESP BOSCH 8.0
Removing and installing steering angle sender -G85- - vehicles with ABS/EDL/TCS/ESP BOSCH 5.7 or ABS/TCS/ESP BOSCH 8.0
The description of the structure and function of the steering angle sender -G85- can be found in self-study programme No. 42.
Special tools and workshop equipment required
t  Vehicle system tester -V.A.G 1552- or vehicle diagnosis, measurement and information system -VAS 5051-
t  Diagnostic cable -V.A.G 1551/3-, -V.A.G 1551/3A-, -V.A.G 1551/3B-, - V.A.G 1551/3C- or -VAS 5051/5A-, -VAS 5051/6A-
Removing:
  WARNING
Disconnect earth strap from the battery before commencing work on the electrical system.
If the battery earth strap is disconnected and connected, carry out certain additional operations → Electrical System → Rep. gr.27.
–  Disconnect battery → Electrical System → Rep. gr.27.
–  Check whether the front wheels are in the straight-ahead position.
–  Remove steering wheel → Body Work → Rep. gr.69.
–  Remove steering column trim → Body Work → Rep. gr.70.
   
The steering angle sender -G85- is fitted together with the coil spring -2- in housing -1-.
   They must not be separated or disassembled.
Pay attention to the steering angle sender -G85- to obtain correct re-installation:
  S48-0188
t  Position the steering angle sender -G85- in the middle position as shown:
   A yellow dot must be visible in the window -1-.
   Markings -arrows- must be flush with each other.
Make sure this correct position is maintained.
  S48-0189
t  Secure the coil spring -2- against unintentional turning by covering it with adhesive tape -1-.
   -3- Housing for steering angle sender -G85-
  S48-0190
–  Disconnect plugs -1- and -2-.
  S45-0199
–  Carefully release catch hooks -arrows-, remove housing -1- with steering angle sender -G85- and coil spring.
Installing:
–  Slide housing -1- with steering angle sender -G85- and coil spring onto the steering column and lock into position with steering column switch -arrows-.
–  Connect both plug connections.
  Note
After removing the transport protection or the adhesive tape do not turn the coil spring, only the positioning of the steering angle sender - G85- in centre position is allowed.
–  Removing transport protection or adhesive tape.
  S48-0191
–  Position the steering angle sender in the centre position:
   A yellow dot must be visible in the window -1-.
   Markings -arrows- must be flush with each other.
Make sure this correct position is maintained.
–  Install steering column trim → Body Work → Rep. gr.70.
–  Install steering wheel → Body Work → Rep. gr.69.
–  Connect battery → Electrical System → Rep. gr.27.
–  Perform null balance of the steering angle sender -G85-.
vehicles with ABS/EDL/TCS/ESP BOSCH 5.7
t  with the vehicle diagnosis, measurement and information system -VAS 5051- → Chapter
or
t  with the vehicle system tester -V.A.G 1552- → Chapter
–  Performing automatic test sequence → Chapter
If a fault is stored in the fault memory:
–  Remove fault → Chapter
–  Erasing fault memory → Chapter
Vehicles with ABS//TCS/ESP BOSCH 8.0
t  with the vehicle diagnosis, measurement and information system -VAS 5051- → Chapter
or
t  with the vehicle system tester -V.A.G 1552- → Chapter
–  Performing automatic test sequence → Chapter
If a fault is stored in the fault memory:
–  Remove fault → Chapter
–  Erasing fault memory → Chapter
  S48-0189

Removing and installing lateral acceleration senderG200 and yaw rate senderG202 or ESP sensor unitG419 - vehicles with ABS/EDL/T > < Setting, removing and installing the brake light switchF