Fabia Mk2
1 - | Clutch housing |
q | is made out of aluminium or magnesium → Chapter |
q | when replacing: Set the differential gear → Chapter |
q | Assignment → Electronic Catalogue of Original Parts |
2 - | Gasket ring for drive shaft |
q | release with a screwdriver |
q | installing → Fig. |
3 - | Ball stud, 20 Nm |
q | grease with grease -G 000 100- |
4 - | Sealing ring |
q | for right flange shaft |
q | replace → Chapter |
5 - | Bushing |
q | for gasket ring |
q | removing → Fig. |
q | installing → Fig. |
6 - | Screw |
q | different versions: → Fig. |
Oil filler plug or oil drain plug with internal serration - 24 Nm |
Oil filler plug or oil drain plug with hexagon socket head - 32 Nm |
7 - | O-ring |
q | only on vehicles without ABS |
q | always replace → Electronic Catalogue of Original Parts |
8 - | Speedometer sender -G22- |
q | only on vehicles without ABS |
9 - | 5 Nm + torque a further 90° |
q | only on vehicles without ABS |
q | always replace → Electronic Catalogue of Original Parts |
10 - | Adjusting washer S2 |
q | for differential gear |
q | Determine thickness → Chapter |
11 - | Outer ring/tapered-roller bearing |
q | for differential gear |
q | removing and installing → Chapter |
q | if the bearing is replaced, set the differential gear → Chapter |
12 - | 5 Nm + torque a further 90° |
q | always replace → Electronic Catalogue of Original Parts |
13 - | Outer ring/tapered-roller bearing |
q | for differential gear |
q | removing and installing → Chapter |
q | if the bearing is replaced, set the differential gear → Chapter |
14 - | Adjusting washer S1 |
q | for differential gear |
q | always 1 mm thick |
q | on gearboxes made out of aluminium as of production date 12.06 the adjusting washer S1 for outer ring/tapered-roller bearing is not fitted → Chapter |
q | Bearing pedestal for outer ring/tapered-roller bearing is adapted |
q | Assignment → Electronic Catalogue of Original Parts |
15 - | Fitting sleeve |
q | (2 pieces) |
16 - | Gearbox housing |
q | is made out of aluminium or magnesium → Chapter |
q | when replacing: Set the differential gear → Chapter |
q | on gearboxes made out of aluminium as of production date 12.06 the adjusting washer S1 (-Pos.14-) for outer ring/tapered-roller bearing is not fitted → Chapter |
q | Bearing pedestal for outer ring/tapered-roller bearing is adapted |
q | Assignment → Electronic Catalogue of Original Parts |
17 - | Oil drain plug |
q | different versions: → Fig. |
Oil filler plug or oil drain plug with internal serration - 24 Nm |
Oil filler plug or oil drain plug with hexagon socket head - 32 Nm |
18 - | Sealing ring |
q | for left flange shaft |
q | replace → Chapter |
19 - | Bushing |
q | for gearshift shaft |
q | extracting → Fig. |
q | inserting → Fig. |
20 - | Magnet |
q | is held in position by the separator surface of the housing |
21 - | Screw cap |
q | Before screwing down cover sealing surface with sealant -AMV 188 200 03- |
22 - | Circlip |
q | inserted in the cylinder roller bearing groove -Pos. 25- |
23 - | Circlip |
q | inserted in the cylinder roller bearing groove -Pos. 24- |
24 - | Cylindrical-roller bearing |
q | for drive shaft |
q | removing and installing → Chapter |
25 - | Cylindrical-roller bearing |
q | for output shaft |
q | removing and installing → Chapter |
26 - | Plug |
q | inserted in the hole in the clutch housing |
|
|
|
Note
|
|
|