Octavia Mk2
| Summary of components |
| 1 - | Screw cap |
| q | Replace seal if damaged |
| 2 - | Oil feed line |
| q | to exhaust gas turbocharger |
| 3 - | Dipstick |
| q | Oil level must not exceed the max. marking! |
| 4 - | Bracket for top auxiliary units |
| q | removing and installing → Chapter |
| 5 - | Gasket |
| q | replace if damaged |
| 6 - | Guide bushing |
| 7 - | Oil filter, 20 Nm |
Note| When removing, make sure that the oil does not penetrate into the generator! Therefore, cover the generator with a clean cloth! |
| q | with gasket rings |
| q | with non-return valve |
| q | slacken and tighten with oil filter wrench -3417- |
| q | Pay attention to change intervals: |
| t | → BookletFabia II |
| t | → BookletRoomster |
| t | → BookletOctavia II |
| t | → BookletYeti |
| 8 - | 25 Nm |
| 9 - | Gasket |
| q | replace if damaged |
| 10 - | 8 Nm + torque a further 90° (1/4 turn) |
| q | replace |
| 11 - | Engine oil cooler |
| q | removing and installing → Chapter |
| 12 - | 8 Nm |
| 13 - | Top timing case |
| q | removing and installing → Chapter |
Caution
|
| 14 - | 25 Nm |
| 15 - | Bottom timing case |
| q | removing and installing → Chapter |
| 16 - | 5 Nm + torque a further 30° |
| q | Screw: M6x20 |
| 17 - | 5 Nm + torque a further 30° |
| q | Screw: M6x40 |
| 18 - | Chain |
| q | removing and installing → Chapter |
| q | for oil pump |
| q | mark running direction (installed position) before removing |
| 19 - | 150 Nm + torque a further 180° (1/2 turn) |
| q | removing and installing → Chapter |
| q | replace |
| q | The clamping surface of the fixing screw must be free of grease and oil. |
| q | insert oiled (thread) |
| 20 - | Belt pulley |
| q | removing and installing → Chapter |
| q | Clamping surfaces must be free of oil and grease. |
| 21 - | Diamond coated washer |
| q | replace |
| 22 - | Sealing ring |
| q | replace |
| q | removing and installing → Chapter |
| 23 - | Bottom cover |
| 24 - | 20 Nm + torque a further 90° (1/4 turn) |
| 25 - | Sprocket |
| q | for oil pump drive |
| q | Clamping surfaces must be free of oil and grease. |
| q | Lock chain sprocket with counterholder -T10172- |
| 26 - | Oil pump |
| q | removing and installing → Chapter |
| q | must be replaced completely |
| 27 - | 13 Nm |
| q | replace |
| q | slacken and tighten only the bolts at the gearbox side with socket insert -T10058- |
| 28 - | 10 Nm |
| 29 - | Oil level and oil temperature sender -G266 - |
| q | replace if damaged |
| q | check → Current flow diagrams, Electrical fault finding and Fitting locations |
| 30 - | Sealing ring |
| q | replace if damaged |
| 31 - | Oil drain plug, 30 Nm |
| q | with captive seal |
| q | replace |
| 32 - | Oil pan |
| q | removing and installing → Chapter |
| 33 - | 14 Nm + torque a further 90° (1/4 turn) |
| 34 - | Sealing ring |
| q | replace |
| 35 - | Suction line |
| 36 - | 8 Nm |
| 37 - | 8 Nm |
| 38 - | Oil separator |
| mount using locking agent -D 176 501 A1- |
