Yeti
| Summary of components - vehicles with four-wheel drive |
Note| t | Before installing heat the inner ring of the tapered-roller bearing to 100°C. |
| t | Replace both tapered-roller bearings together. |
| t | When replacing the tapered-roller bearings, the differential housing, the gearbox housing or the clutch housing, set the differential gear → Chapter. |
| 1 - | Gearbox housing |
| 2 - | Adjusting washer |
| q | for differential gear |
| q | Determine thickness → Chapter |
| 3 - | Outer ring/tapered-roller bearing |
| q | removing → Fig. |
| q | pressing on → Fig. |
| 4 - | Inner ring/tapered-roller bearing |
| q | remove → Fig. |
| q | pressing on → Fig. |
| 5 - | Differential gear housing |
| q | with riveted pinion for final drive |
| 6 - | Inner ring/tapered-roller bearing |
| q | remove → Fig. |
| q | pressing on → Fig. |
| 7 - | Outer ring/tapered-roller bearing |
| q | removing → Fig. |
| q | pressing on → Fig. |
| 8 - | Pressure washer |
| q | Fitting position: the shoulder on the inside diameter points towards the angular gearbox Pos. 18 |
| 9 - | Clutch housing |
| 10 - | Sealing ring |
| q | between manual gearbox and angle gearbox |
| q | replace → Chapter |
| q | pull out using ejection lever -MP3-418- or ejection lever -T20143/2- |
| q | on disassembled gearbox it can be driven in with pressure plate -T40007- up to the stop |
| 11 - | Sealing ring |
| q | for right flange shaft |
| q | diameter of left and right differ |
| q | replace with installed manual gearbox with angle gearbox → Chapter |
| 12 - | 40 Nm + torque a further 90° |
| q | 4 pieces |
| q | always replace → Electronic Catalogue of Original Parts |
| 13 - | 33 Nm |
| q | screw into threaded piece Pos. 24 |
| 14 - | Right flange shaft |
| q | removing and installing → Chapter |
| 15 - | Sealing ring |
| q | to replace, remove the needle bearings (polygon bearing ) pos. 16 |
| 16 - | Needle bearing (polygon bearing) |
| q | replace → Chapter |
| 17 - | Circlip |
| q | always replace → Electronic Catalogue of Original Parts |
| 18 - | Angle gearbox |
| q | Removing and installing with gearbox fitted → Chapter |
| q | Removing and installing with gearbox removed → Chapter |
| 19 - | Sealing ring |
| q | between angle gearbox and manual gearbox |
| q | replace with angle gearbox removed → Chapter |
| 20 - | Differential bevel gear, large |
| q | installing → Fig. |
| 21 - | Differential bevel gear shaft |
| q | removing → Fig. |
| q | installing → Fig. |
| 22 - | Tensioning sleeve |
| q | to secure the differential bevel gear shaft |
| q | removing → Fig. |
| q | drive in the new tensioning sleeve → Fig. flush |
| 23 - | Differential bevel gear small |
| q | installing → Fig. |
| 24 - | Threaded part |
| q | installing → Fig. |
| 25 - | Stop disc compound |
| q | insert with gear oil |
| 26 - | Circlip |
| q | holds the conical ring, stop disc and pressure spring in position when the flange shaft is removed |
| 27 - | Conical ring |
| q | with slots (if present) for thrust washer catch |
| q | Fitting position: Cone towards differential gear housing |
| 28 - | Thrust washer |
| q | Fitting position: Collar to pressure spring, legs (if present) to conical ring |
| 29 - | Pressure spring for left flange shaft |
| q | fitted behind left flange shaft |
| 30 - | Flange shaft left |
| 31 - | Sealing ring |
| q | for left flange shaft |
| q | diameter of left and right differ |
| q | replace with installed gearbox → Chapter |