Replace carpet - complete - L69
Remove
2. |
Wait 1 minute for airbag to deactivate
|
3. |
Detach front seat belt securing panel - both sides
• |
Unclip panel upwards (1)
|
|
4. |
Detach seat belt from front seat - both sides
|
|
|
5. |
Detach rear of front seat - both sides
|
6. |
Remove front seat - both sides
• |
Remove from front guide
|
• |
Release and disconnect compact connector
|
|
|
|
7. |
Detach footwell instrument panel padding left and right
• |
Unscrew 2x bolts (1) on driver's side and remove footwell
panelling from bracket
|
• |
Unscrew 2x screws (2) on passenger's side and remove footwell
panelling from bracket
|
|
|
|
8. |
Detach central console
|
9. |
Remove sill strip completely - both sides
• |
Remove inner panelling sill upwards
|
|
|
|
10. |
Detach instrument panel padding fastening stations - both
sides
|
|
|
11. |
Detach lower C-pillar panel - left side
|
12. |
Detach lower C-pillar panel - right side
|
13. |
Remove airbag control unit
• |
Unscrew 3x nuts (1) and remove control unit
|
|
14. |
Loosen airbag wiring harness
• |
Release 2x wiring harness plugs and disconnect
|
• |
Loosen cable harness clamp
|
• |
Separate hand brake wiring harness plug
|
• |
Detach earth cable and place to one side
|
• |
Unclip diagnostics plug
|
|
|
|
15. |
Remove diagnostics plug bracket
|
16. |
Loosen shifter rod in the engine compartment
Note: Mark installation
position.
|
17. |
Remove cage
• |
Unscrew 4x screws and remove cage with shifter rod
|
|
|
|
18. |
Remove carpet beginning from rear
Note: 2nd mechanic
required.
|
|
|
Install
19. |
Lay carpet beginning at the front
Note: A second mechanic
is required
|
20. |
Install cage
• |
Place cage and tighten 4x screws
|
|
21. |
Fasten shifter rod in the engine compartment
Note: Observe the
installation position!
|
22. |
Install diagnostics plug bracket
|
23. |
Fasten airbag wiring harness
• |
Fasten cable harness clamp
|
• |
Connect wiring harness plug
|
• |
Clip in diagnostics plug
|
|
24. |
Install airbag control unit
• |
Connect 2x wiring harness plugs
|
|
25. |
Attach instrument panel padding fastening stations - both
sides
|
26. |
Attach footwell instrument panel padding left and right
• |
Insert footwell panelling in bracket and screw in 2x screws on
passenger's side
|
• |
Insert footwell panelling in bracket and screw in 2x screws on
passenger's side
|
|
27. |
Install centre console
|
28. |
Install sill strip completely - both sides
• |
Insert sill strip into guide
|
|
29. |
Insert front seat - both sides
• |
Connect and latch compact connector
|
• |
Insert seat in front guide
|
|
30. |
Fasten front seats - both sides
• |
Tighten 2x bolt 35 Nm
Note: Use screw locking
compound
|
|
31. |
Attach seat belt to front seat - both sides
• |
Tighten bolt 20 Nm
Note: Use screw locking
compound
|
|
32. |
Insert front seat panel - both sides
• |
Place front seats in original position
|
|
33. |
Attach lower C-pillar panel - left side
|
34. |
Attach lower C-pillar panel - right side
|
36. |
Program volatile memories
|
|