Replace carpet - complete - L70
Remove
2. |
Wait 1 minute for airbag to deactivate
|
3. |
Place seats in the forward-most position
|
4. |
Detach belt securing panel - driver's side
• |
Unclip panel upwards (1)
|
|
5. |
Detach belt securing panel - passenger side
• |
Unclip panel upwards (1)
|
|
6. |
Attach seat belt at front seat - driver's side
|
7. |
Attach seat belt at front seat - passenger's side
|
|
|
8. |
Detach driver's side front seat
|
9. |
Detach passenger side front seat
|
10. |
Remove driver's side front seat
• |
Remove from front guide
|
• |
Release and disconnect compact connector
|
|
11. |
Remove passenger's side front seat
• |
Remove from front guide
|
• |
Release and disconnect compact connector
|
|
|
|
12. |
Detach footwell instrument panel padding left and right
• |
Unscrew 2x screws on driver's side and remove footwell
panelling from bracket
|
• |
Unscrew 2x screws on passenger's side and remove footwell
panelling from bracket
|
|
|
|
13. |
Detach central console
|
14. |
Remove sill inner panelling - both sides
|
|
|
15. |
Remove airbag control unit
• |
Unscrew 3x nuts (1) and remove control unit
|
• |
Release 2x wiring harness plugs and disconnect
|
|
|
|
16. |
Remove bracket from diagnostics plug (1)
|
|
|
|
17. |
Loosen cable duct (1)
• |
Disconnect 2x wiring harness plugs (2)
|
|
|
|
18. |
Remove instrument panel padding bracket - both sides
|
|
|
19. |
Loosen shift cable
• |
Remove retaining clip (2)
|
|
20. |
Open up wiring harness
• |
Separate gear stick wiring harness plug (3)
|
• |
Separate hand brake wiring harness plug (4)
|
|
|
21. |
Remove automatic gearbox control unit
|
|
22. |
Remove carpet
• |
Open quick release fastener (1)
|
• |
Unclip wiring harness clip (2)
|
|
|
Install
23. |
Install carpet - completely
• |
Close quick release fastener
|
• |
Attach wiring harness clip
|
|
24. |
Install automatic gearbox control unit
|
26. |
Attach wiring harness
• |
Connect hand brake wiring harness plug
|
• |
Connect gear shift wiring harness plug
|
|
27. |
Attach instrument panel padding bracket - both sides
|
28. |
Fasten cable duct
• |
Connect 2x wiring harness plugs
|
|
29. |
Install diagnostics plug bracket
|
30. |
Install airbag control unit
• |
Connect and lock 2x wiring harness plug
|
|
31. |
Install sill inner panelling
|
32. |
Install centre console
|
33. |
Attach footwell instrument panel padding left and right
• |
Tighten 2x bolts driver's side
|
• |
Tighten 2x bolts passenger's side
|
|
34. |
Install sill strip completely - both sides
|
35. |
Insert driver's side front seat
• |
Connect and latch compact connector
|
• |
Insert seat in front guide
|
|
36. |
Fasten driver's side front seat
• |
Tighten 2x bolt 35 Nm
Note: Use screw locking
compound
|
|
37. |
Attach seat belt driver's side
• |
Tighten bolt 20 Nm
Note: Use screw locking
compound
|
|
38. |
Insert driver's side front seat panel
• |
Place front seat in original position
|
|
39. |
Insert front seat - passenger side
• |
Connect and latch compact connector
|
• |
Insert seat in front guide
|
|
40. |
Fasten passenger side - front seat
• |
Tighten 2x bolt 35 Nm
Note: Use screw locking
compound
|
|
41. |
Attach seat belt on passenger's side
• |
Tighten bolt 20 Nm
Note: Use screw locking
compound
|
|
42. |
Insert passenger's side front seat panel
• |
Place front seat in original position
|
|
44. |
Program volatile memories
|
|