vauxhall Workshop Repair Guides

Vauxhall Workshop Service and Repair Manuals

ABOUT US
C-018 No Communication with SDM > < C-016 No Communication with REC

Astra H

C-017 - No Communication with PAS

Test

Work Order Description

Nominal Value
T001

Check: Interruption of Voltage Supply Circuit
  • Ignition OFF
  • All consumers turned off
  • Disconnect wiring harness connector from:
    A146 Control Unit - Park Pilot
    (Wiring Harness Connector XC22 )
    &
    Diagnostic tester
  • Ignition ON
  • Measure voltage between the following terminals:
    A146 Control Unit - Park Pilot
    Wiring harness connector (wiring harness side) terminal 7(XC22)
    &
    Ground

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:
T002

Check: Interruption of Voltage Supply Circuit
  • Measure voltage between the following terminals:
    A146 Control Unit - Park Pilot
    Wiring harness connector (wiring harness side) terminal 8(XC22)
    &
    Battery voltage

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:
T003

Check: Interruption of Voltage Supply Circuit
  • Ignition OFF
  • Remove electrical component from socket:
    FR13 Fuse
  • Ignition ON
  • Measure voltage between the following terminals:
    FR13 Fuse
    Input contact
    &
    Ground

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:
T004

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Astra-H, Hatchback
Astra-H, Convertible
Astra-H, Station Wagon
Yes: No:
T005

Check: Vehicle Configuration

Is the following information correct for the actual vehicle?

Astra-H, Notchback
Yes: No:
T006

Check: Interruption of Voltage Supply Circuit
  • Ignition OFF
  • Remove electrical component from socket:
    K1_X131 Relay - Terminal 15
  • Ignition ON
  • Measure voltage between the following terminals:
    K1_X131 Relay - Terminal 15
    Socket Terminal 30
    &
    Ground

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:
T007

Check: Interruption of Voltage Supply Circuit
  • Ignition ON
  • Measure voltage between the following terminals:
    K1_X131 Relay - Terminal 15
    Socket Terminal 86
    &
    Ground

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:
T008

Check: Interruption of Voltage Supply Circuit
  • Ignition ON
  • Measure voltage between the following terminals:
    K1_X131 Relay - Terminal 15
    Socket Terminal 85
    &
    Battery voltage

greater than 11 V
Voltage Measurement Current Value: V
Yes: No:


Result

Cause Of Fault
E001 Result: Interruption
  • Circuit interruption between:
    A146 Control Unit - Park Pilot
    Wiring harness connector (wiring harness side) terminal (Convertible) 1 (XC88) (Van) 1 (XC21) (Notchback) 1 (XC88) (2008 - 2010), (Hatchback) (2008 - 2011), (Station Wagon) 1 (XC88)
    &
    X131 Rear Electronic Module
    Wiring harness connector (wiring harness side) terminal (Convertible) 5 (XR1) (Van) 30(XR5) (Notchback) 5 (XR1) (2008 - 2010), (Hatchback) (2008 - 2011), (Station Wagon) 5 (XR1)

or

  • Defective component:
    A146 Control Unit - Park Pilot
    or
    X131 Rear Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.

Note:

The replacement of the components must be done in the listed order.

The system must be checked for proper operation after every replacement.

-

Station Wagon

&

Vehicle with hatchback:

During model year 2007 the following changes occur:

The wiring harness connector terminal changes from 1 (XC21) to 1 (XC88)

and

The wiring harness connector terminal changes from 30 (XR5) to 5 (XR1)
E002 Result: Interruption
  • Circuit interruption between:
    A146 Control Unit - Park Pilot
    Wiring harness connector (wiring harness side) terminal 8(XC22)
    &
    Ground
E003 Result: Interruption
  • Circuit interruption between:
    X131 Rear Electronic Module
    Wiring harness connector (wiring harness side) terminal 1(XR2)
    &
    A146 Control Unit - Park Pilot
    Wiring harness connector (wiring harness side) terminal 7(XC22)
E004 Result: Interruption
  • Circuit interruption between:
    X131 Rear Electronic Module
    Wiring harness connector (wiring harness side) terminal 1(XR2)
    &
    X131 Rear Electronic Module
    Wiring harness connector (wiring harness side) terminal 3 (XR5)
    or
    X131 Rear Electronic Module
    Wiring harness connector (wiring harness side) terminal 18 (XR1)
    &
    A146 Control Unit - Park Pilot
    Wiring harness connector (wiring harness side) terminal 7 (XC22)

or

  • Defective component:
    X131 Rear Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E005 Invalid / not supported vehicle configuration
  • The selected Checking Procedure is not valid for this vehicle configuration.
E006 Result: Defective Component
  • Defective component:
    K1_X131 Relay - Terminal 15
    or
    X131 Rear Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.

Note:

The replacement of the components must be done in the listed order.

The system must be checked for proper operation after every replacement.
E007 Result: Interruption
  • Circuit interruption between:
    X131 Rear Electronic Module
    Wiring harness connector (wiring harness side) terminal 18(XR4)
    &
    Ground

or

  • Defective component:
    X131 Rear Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E008 Result: Interruption
  • Circuit interruption between:
    X131 Rear Electronic Module
    Wiring harness connector (wiring harness side) terminal 57(XR5)
    &
    A105 Column Integrated Module
    Wiring harness connector (wiring harness side) terminal 2

or

  • Defective component:
    X131 Rear Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.
E009 Result: Defective Component
  • Defective component:
    X131 Rear Electronic Module

Important:

Reset the concerned control unit with the diagnostic tester before replacing it. In order to do that, call up the "RESET" function from the PROGRAMMING menu of the current system on the diagnostic tester.





C-018 No Communication with SDM > < C-016 No Communication with REC