Crankshaft services PULLEY - R.R.

Operation 1092A10 · Crankshaft pulley and idle pulleys

1.6 TS

Removing

Position the vehicle on the ramp.

Proceed with the removal - 4450B10 Front WHEEL (one) - R.R. (Right side).

Proceed with the removal - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side).

Proceed with the removal - 1092G10 single engine belt r r.

1. Undo the bolts (1a) and remove the crankshaft pulley (1b).

Refitting

Place the crankshaft pulley back in its housing and secure it tightening the bolts to the recommended torque.

Proceed with the refitting - 1092G10 single engine belt r r.

Proceed with the refitting - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side).

Proceed with the refitting - 4450B10 Front WHEEL (one) - R.R. (Right side).

Remove the car from the ramp.

2.0 TS

Removing

Position the vehicle on the ramp.

Proceed with the removal - 4450B10 Front WHEEL (one) - R.R. (Right side).

Proceed with the removal - 7055B54 under-engine guard - r r.

Proceed with the removal - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side).

Proceed with the removal - 1092G10 single engine belt r r.

1. Undo the bolts (1a) and remove the crankshaft pulley (1b).

Refitting

Place the crankshaft pulley back in its housing and secure it tightening the bolts to the recommended torque.

Proceed with the refitting - 1092G10 single engine belt r r.

Proceed with the refitting - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side).

Proceed with the refitting - 7055B54 under-engine guard - r r.

Proceed with the refitting - 4450B10 Front WHEEL (one) - R.R. (Right side).

Remove the car from the ramp.

3.2 V6

Removing

Position the vehicle on the ramp.

Proceed with removal - 4450B08 right rear wheel r r.

Proceed with removal - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R..

Proceed with removal - 1092G10 single engine belt r r.

1. Fit the crankshaft pulley counter-torque tool.

2. Slacken the crankshaft pulley nut.

Remove the crankshaft pulley counter-torque tool.

1. Fully undo the nut (1a) and remove the crankshaft pulley (1b).

Refitting

Place the crankshaft pulley back in its housing and secure it without tightening the nut.

1. Fit the crankshaft pulley counter-torque tool.

2. Tighten the crankshaft pulley nut to the specified torque.

Remove the crankshaft pulley counter-torque tool.

Proceed with refitting - 1092G10 single engine belt r r.

Proceed with refitting - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R..

Proceed with refitting - 4450B08 right rear wheel r r.

Remove the car from the ramps.

1.9 JTD 8V

Removing

Place the car on a ramp.

- 7055B54 under-engine guard - r r

- 4450B04 right front wheel r r

- 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R.

- 1092G10 single engine belt r r

1. Unscrew the retaining bolts (1a) and remove the lower flywheel protection (1b).

2. Fit the flywheel lock.

1. Undo the fixing bolts (1a) and remove the auxiliary shaft drive pulley (1b).

Refitting

Fit the auxiliary shaft drive pulley.

Tighten the bolts fixing the pulley to the crankshaft to torque.

Remove the flywheel lock.

Fit the engine flywheel lower protection.

- 1092G10 single engine belt r r

- 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R.

- 4450B04 right front wheel r r

- 7055B54 under-engine guard - r r

Remove the vehicle from the ramp.

1.9 JTD 16V

Removing

Position the vehicle on the ramp

Proceed with removal - 4450B04 right front wheel r r.

Proceed with removal - 7055B54 under-engine guard - r r.

Proceed with removal - 7055B91 Right front WHEEL ARCH LINER - R.R..

Proceed with removal - 1092G10 single engine belt r r.

1. Undo the bolts (1a) and remove the crankshaft pulley (1b).

Refitting

1. Place the crankshaft pulley (1a) back in its seating and secure it tightening the bolts (1b) to the specified torque.

.Proceed with refitting - 1092G10 single engine belt r r.

.Proceed with refitting - 7055B91 Right front WHEEL ARCH LINER - R.R..

.Proceed with refitting - 7055B54 under-engine guard - r r.

.Proceed with refitting - 4450B04 right front wheel r r.

Remove the car from the ramps.